15 September 2021 in Journal of Fluid Mechanics
Large-eddy simulations are used to investigate the origin of the wake asymmetry and symmetry behind notchback Ahmed bodies. Two different effective backlight angles, ${\beta _1} = 17.8\mathrm{^\circ }$ and ${\beta _2} = 21.0\mathrm{^\circ }$ , are simulated resulting in wake asymmetry and symmetry in flows without external perturbations, in agreement with previous experimental observations. In particular, the asymmetric case presents a bi-stable nature showing, in a random fashion, two stable mirrored states characterized by a left or right asymmetry for long periods. A random switch and several attempts to switch between the bi-stability are observed. The asymmetry of the flow is ascribed to the asymmetric separations and reattachments in the wake. The deflection of the near-wall flow structures behind the slant counteracting the asymmetry drives the wake to be temporarily symmetric, triggering the switching process of the bi-stable wake. The consequence of deflection that forces the flow structure to form on the opposite side of the slant is the decisive factor for a successful switch. Modal analysis applying proper orthogonal decomposition is used for the exploration of the wake dynamics of the bi-stable nature observed.
20 April 2020 in Journal of Fluid Mechanics
The control of bluff-body wakes for reduced drag and enhanced stability has traditionally relied on the so-called direct-wake control approach. By the use of actuators or passive devices, one can manipulate the aerodynamic loads that act on the rear of the model. An alternative approach for the manipulation of the flow is to move the position of the actuator upstream, hence interacting with an easier-to-manipulate boundary layer. The present paper comprises a bluff-body flow study via large-eddy simulations to investigate the effectiveness of an upstream actuator (positioned at the leading edge) with regard to the manipulation of the wake dynamics and its aerodynamic loads. A rectangular cylinder with rounded leading edges, equipped with actuators positioned at the front curvatures, is simulated at . A genetic algorithm (GA) optimization is performed to find an effective actuation that minimizes drag. It is shown that the GA selects superharmonic frequencies of the natural vortex shedding. Hence, the induced disturbances, penetrating downstream in the wake, significantly reduce drag and lateral instability. A comparison with a side-recirculation-suppression approach is also presented, the latter case being worse in terms of reduced drag (only 8 % drag reduction achieved), despite the total suppression of the side recirculation bubble. In contrast, the GA optimized case contributes to a 20 % drag reduction with respect to the unactuated case. In addition, the large drag reduction is associated with a reduced shedding motion and an improved lateral stability.
30 August 2016 in Flow, Turbulence and Combustion
Large Eddy Simulations (LES) are conducted to study the actuated flow field around a bluff body. The model is a simplified section of a truck. The aim of the work is to model the separation of the flow acting at the front rounded corners, the so called A-pillars, and to minimize the separation of the flow by means of Zero Net Mass Flux synthetic jets. LES data show the interaction of the flow main structures, the separation mechanism and the effects of the actuation on the flow field. The flow is post processed using modal and frequency decompositions. Relevant results in terms of drag reduction were observed for the actuated flow. The principle flow mechanisms are discussed and an optimal actuation frequency, in terms of induced fluctuations and drag reduction, is identified.
29 November 2021 in Journal of Fluid Mechanics
The wake of a notchback Ahmed body presenting a bi-stable nature is investigated by performing wind tunnel experiments and large-eddy simulations. Attention is confined to the Reynolds number ( $Re$ ) influence on the wake state instability within $5\times 10^{4}\leq Re \leq 25\times 10^{4}$ . Experimental observations suggest a wake bi-stability with low-frequency switches under low $Re$ . The wake becomes ‘tri-stable’ with the increase of $Re$ with the introduction of a new symmetric state. The higher presence of the symmetric state can be considered as a symmetrization of the wake bi-stability with an increasing $Re$ . The wake symmetry under high $Re$ attributed to the highly frequent switches of the wake is extremely sensitive to small yaw angles, showing the feature of bi-stable flows. The wake asymmetry is confirmed in numerical simulations with both low and high $Re$ . The wake asymmetries are indicated by the wake separation, the reattachment and the wake dynamics identified by the proper orthogonal decomposition. However, the turbulence level is found to be significantly higher with a higher $Re$ . This leads to a higher possibility to break the asymmetric state, resulting in highly frequent switches showing symmetry.
25 September 2018 in Flow, Turbulence and Combustion
Recent experimental investigations by McArthur et al. (J. Fluids Struct. 66, 293–314, 2016 ) in the wake of a simplified heavy vehicle or commonly known as the ground transportation system (GTS) model has shown that the flow topology is invariant over a large range of Reynolds numbers [2.7 × 104 − 2 × 106]. Numerical simulations are performed to investigate the initial flow topology at a Reynolds number of 2.7 × 104, using well-resolved large eddy simulations (LES). In the vertical midplane behind the GTS, a flow state which is anti-symmetric to that reported in McArthur et al. (J. Fluids Struct. 66, 293–314, 2016 ) is observed here, thereby, confirming the possibility of occurrence of the complementary bi-stable flow state. The occurrence of this bi-stable state does not depend on the ground clearance between the GTS and the ground plane, as a similar flow topology is observed at both small and large gap heights. Furthermore, the flow topology in the vertical midplane is also found to be insensitive to the incoming flow for small yaw angles. However, complex flow behaviour is observed in the wake for larger yaw angles, where the flow topology in the vertical midplane becomes nearly symmetric, while an asymmetric flow topology is now observed in the lateral midplane in the near wake. Furthermore, the corner vortices which originate from either side at the front of the model merge in the far wake, leading to a large vortex structure nearly equal to the height of the model. The near-wake topology of the GTS is analysed and compared with previous studies for a range of scenarios, and the forces on the GTS are computed.
1 March 2019 in Journal of Wind Engineering and Industrial Aerodynamics