L.M.S. Santos

L.M.S. Santos

Auto-generated profile, based on publicly available information

L.M.S. Santos


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2019 in Theoretical and Applied Fracture Mechanics
Verified
Journal Article
Closed access
LSL.M.S. Santos
L.M.S. Santos
LBLuis Filipe Borrego
Luis Filipe Borrego
JFJ.A.M. Ferreira
J.A.M. Ferreira
Joel Alexandre da Silva de JesusJoel Alexandre da Silva de Jesus
Joel Alexandre da Silva de Jesus
JCJOSE COSTA
JOSE COSTA
CCCarlos Capela
Carlos Capela

1 October 2016 in Theoretical and Applied Fracture Mechanics
Verified
Journal Article
Closed access
LSL.M.S. Santos
L.M.S. Santos
FJosé Ferreira
José Ferreira
Joel Alexandre da Silva de JesusJoel Alexandre da Silva de Jesus
Joel Alexandre da Silva de Jesus
JCJOSE COSTA
JOSE COSTA
CCCarlos Capela
Carlos Capela

1 January 2016 in Procedia Structural Integrity
Verified
Journal Article
Open access
JFJ.A.M. Ferreira
J.A.M. Ferreira
LSL.M.S. Santos
L.M.S. Santos
Joel Alexandre da Silva de JesusJoel Alexandre da Silva de Jesus
Joel Alexandre da Silva de Jesus
JCJOSE COSTA
JOSE COSTA
CCCarlos Capela
Carlos Capela
The construction of hybrid parts: comprised of two different materials or obtained by two distinct technological processes is one of the main advantages of laser sintering metal. Various important aspects strongly affect the mechanical properties of sintering metal components: porosity, surface roughness, scan speed, layer thickness, and residual stresses. A major drawback is the occurrence of pores originating from initial powder contaminations, evaporation or local voids after powder-layer deposition, once these pores can act as stress concentrators leading to failure, especially under fatigue loading.The purpose of present work was to study the effect scan speed on the porosity and mechanical properties. Also the performance of two different material parts was studied. The sintering laser parts were manufactured in maraging steel AISI 18Ni300, while the substrates of hybrid specimens were produced alternatively in two materials: the steel for hot work tools AISI H13 and the stainless steel AISI 420.The results showed that a very high scan speed (400 or 600 mm/s) causes the appearance of high porosity percentages and consequent drastic reduction of tensile strength and stiffness. Tensile properties of sintered specimens and two different material parts was similar. However, the fatigue strength of two different material parts tends to decrease, for long lives, when compared with single sintered specimens

1 January 2016 in Procedia Engineering
Verified
Journal Article
Open access
LSL.M.S. Santos
L.M.S. Santos
FJosé Ferreira
José Ferreira
JCJOSE COSTA
JOSE COSTA
CCCarlos Capela
Carlos Capela
Laser sintering metal has recently been used in the manufacture of metallic structural hybrid components comprising two different materials obtained by two distinct technological processes. This process allows to obtain productivity gains reducing sintering time and hence the cost. In current study it was used a machined substrate in which it is built by sintering the remaining part. The purpose of present work was to study the effect of the substrate material and interface microstructure on the fatigue performance under constant and variable block loadings. The sintering laser parts were manufactured in maraging steel AISI 18Ni300, while the substrates of hybrid specimens were produced alternatively in two materials: the steel for hot work tools AISI H13 and the stainless steel AISI 420. Fatigue strength will be quantified in terms of S - N curves. The results show that tensile properties of sintered specimens and of the hybrid parts was similar. Fatigue strength for short lives, of the sintered specimens and hybrid parts was quite similar. However, the fatigue strength of hybrid parts tends to decrease, for long lives, when compared with single sintered specimens. The fatigue tests under block loadings leads to indicate that the application of Miner's law is adequate to predate fatigue life in hybrid components with sintered implants, despite having been observed a tendency to be conservative for long life