29 December 2015 in IEEE Transactions on Vehicular Technology
In view of the nonuniform voltage of series-connected supercapacitors (SCs), a new voltage equalizer was designed. This voltage equalizer is composed of a switching network circuit and an isolated dc/dc converter. A switching network greatly simplifies the circuit over a traditional switch driver by using electrical potential difference between series-connected SCs to drive switches. It provides pathways for all SCs that are series connected. Each SC can be connected to an isolated dc/dc converter individually by the use of a switching network. Energy will be transmitted between any two cells directly; thus, it is also called point-to-point energy transmission. Detailed operation analyses and an equalizing strategy were presented for the voltage equalizer. A prototype for 12 SCs that are series connected was built based on the new voltage equalizer, and an experiment was performed for series-connected SCs with a nonuniform initial voltage. The experimental results showed that the voltage equalizer has the ability to eliminate nonuniform voltage of the series-connected SCs effectively. Furthermore, this voltage equalizer not only can be used for SCs but can be used for traditional secondary batteries as well.
13 March 2018 in IEEE Transactions on Electron Devices
This paper presents the design and simulation of a broadband Ka-band gyrotron traveling-wave tube operating in the TE 02 d mode at the fundamental cyclotron harmonic with a fully dielectric-loaded circuit. Through loading loss-free dielectric on the entire circuit, the dispersion properties of the circuit are changed to maintain resonance condition at a wide frequency band. A sliced lossy dielectric-loaded structure is employed to provide the required loss for stable operation. The interaction circuit is analyzed under the field matching theory, the nonlinear self-consistent theory, and particle-in-cell codes. A saturated peak output power of 100 kW is achieved at 29 GHz, corresponding to a saturated gain of 44 dB and an efficiency of more than 15% within a 3-dB saturated bandwidth of 6.1 GHz (20% relative bandwidth).
20 February 2017 in IEEE Transactions on Electron Devices
The propagation characteristics of a confocal waveguide are related to the radial spheroidal function, which is extremely complicated. A quadratic polynomial fitting (QPF) expression derived from numerical results by interpolation was successfully applied to the development of confocal gyrotrons. However, the QPF expression is valid only for a moderate spheroidal parameter. As a result, it cannot work well for confocal gyrotron travelling-wave tube (gyro-TWT) applications since the Fresnel parameter may be small for stable operations. For the first time, an efficient algorithm is developed to accurately calculate the spheroidal functions. Based on it, the MATLAB code with high accuracy and efficiency is developed to analyze the propagation characteristics of confocal waveguide. The calculated results and the QPF results are compared for different mirror apertures, and then demonstrated by high frequency structure simulator (HFSS). The calculated results show good agreement with the HFSS results for different mirror apertures while the QPF solution agrees with the HFSS results only for large apertures. The code is valid for arbitrary mirror apertures for both the confocal gyrotron and gyro-TWT applications.
23 January 2018 in IEEE Electron Device Letters
In this letter, diffractive-wave feedback mechanism of confocal gyrotron travelling-wave amplifiers (gyro-TWAs) is presented and verified in cold-test experiments for the first time. The reason for this physical mechanism is that part of the diffractive wave re-enters the open circuit during outward radiation. The achieved circuit loss is less than the theoretical predictions without considering the feedback. This abnormal behavior will seriously deteriorate the stability of the amplifiers including potential near-cutoff instability and backward-wave oscillation, presenting as a main factor that greatly degrades the performance of confocal gyro-TWAs, especially in high-gain operation.
12 July 2016 in IEEE Transactions on Electron Devices
In this paper, a novel triode-type magnetron injection gun (MIG) with three emitters designed for gyrotron traveling wave amplifiers has been presented. This MIG can be operated in Ku/Ka/Q single band or Ku-Ka/Ka-Q dual band. The optimization of the MIG is accomplished by a multiobjective genetic algorithm method. It is anticipated that this MIG possesses an axial velocity spread of <;5% in all the operating frequency bands. The results of sensitivity study show that this MIG can work stably within reasonable parametric windows. Velocity spreads considering cathode surface roughness and initial thermal temperature are analyzed. Cathode configuration with heat insulation chambers is introduced to cut off the thermal flow among the emitters. Thermal analysis has been performed.
13 September 2016 in IEEE Transactions on Electron Devices
This paper is intended to propose the numerical methodology in optimizing the cusp gun for a 70-kV, 1-A W-band gyrotron traveling wave amplifier working at the second-harmonic TE21 mode. Two numerical methods using the simulated annealing algorithm (SAA) and genetic algorithm (GA) are adopted to perform the gun optimization. Classical electron optics software EGUN is employed to compute the beam trajectories. Maintaining the velocity ratio around 1.6, the axial velocity spreads optimized by SAA and GA are 1.44% and 0.33%, respectively, which means a great improvement compared with the manually optimized value of 2.78%. An analysis of the impact of parametric fluctuation on beam quality indicates that this cusp gun can be stably operated within a reasonable parameter scope. This paper will help to enhance the efficiency of electron gun design for gyrotron devices.