1 November 2017 in Journal of Physics D: Applied Physics
The splashing erosion of electrodes in a DC atmospheric-pressure air arc has been investigated by visualization of the electrode surface and the sputtered droplets, and tracking of the droplet trajectories, using image processing techniques. A particle tracking velocimetry algorithm has been introduced to measure the sputtering velocity distribution. Erosion of both tungsten–copper and tungsten–ceria electrodes is studied; in both cases electrode erosion is found to be dominated by droplet splashing rather than metal evaporation. Erosion is directly influenced by both melting and the formation of plasma jets, and can be reduced by the tuning of the plasma jet and electrode material. The results provide an understanding of the mechanisms that lead to the long lifetime of tungsten–copper electrodes, and may provide a path for the design of the electrode system subjected to electric arc to minimize erosion.
5 September 2019 in Journal of Physics D: Applied Physics
This research concentrates on the erosion mechanism of the W 70 Cu 30 anode in DC gaseous arcs. An in situ diagnostic system including the measurement of the anode surface temperature and the fast-imaging of the erosion process was developed. The influence of gas media He, N 2 , H 2 , Ar and current, varying from 50 A to 400 A, was investigated. Two erosion modes were observed, namely an evaporation-dominated mode and a splash-dominated mode. The results indicate that the detachment of the splashing droplet is driven by the explosion of surface bubbles, and it is the surface temperature of the anode that determines the size of the surface bubble as well as the splashing erosion rate. Moreover, the prior vaporization of Cu dispersed in the W 70 Cu 30 anode limits the fusion of the W skeleton but promotes the generation of molten ejections by the explosions of Cu vapor bubbles when the topmost Cu is absent. The large difference between W and Cu in melting and boiling temperatures controls the formation of the molten pool on the W 70 Cu 30 anode and leads to the transition of the two erosion modes. The experimental results contribute to a fundamental understanding of the interaction between thermal plasmas and materials.
13 July 2021 in Journal of Physics D: Applied Physics
Microparticles are an inevitable component of vacuum arcs. This paper focused on the dynamics of microparticle and erosion behavior in high-current vacuum arcs. The arc was sustained with AC 110 Hz between two butt CuCr alloy contacts with a diameter of 10 mm. An in situ microparticle diagnostic system suitable for vacuum arcs was developed. Three sources of microparticles were observed and the corresponding motion characteristics were obtained by our method. The influence of current and Cr content on erosion characteristics was investigated. The results indicate that the increase of Cr content contributes to inhibiting production of microparticles when the current is small. CuCr30 has the best effect of suppressing microparticle production among the three tested alloy materials under large current. The work of this paper helps with the understanding of microparticle behavior in high-current vacuum arcs and may provide a path for the design of a vacuum electrode.
2 September 2020 in Journal of Physics D: Applied Physics
Based on the in situ diagnostic system and the digital image post-processing technique, quantifications of the anodic erosion components and heat transfer efficiency for tungsten and the W 80 Ag 20 material in arcs of argon, helium, and nitrogen were achieved. The leading vaporization of silver has been found to result in evidently lower anodic heat transfer efficiency and much smaller molten pools compared with those of the tungsten anode, but the intensive generation of silver vapor under the melt layer causes higher splashing erosion of the W 80 Ag 20 anode. However, these characteristics can be strongly changed by the cathodic blowing, which leads to a much higher splashing erosion of tungsten anode but a lower erosion rate of W 80 Ag 20 anode. Through the visualization of the erosion behavior and the post microanalysis of the anode surface, the possible driving mechanisms for the generation of the splashing droplet were discussed. The result indicates that the local high pressure caused by the vapor blasting during the bubble explosion plays a key role in the detachment of splashing droplets. Furthermore, as for the tungsten-based anode, the comparison of erosion behavior between the W 80 Ag 20 anode and the previous-studied W 70 Cu 30 anode makes it clear that increasing the temperature difference between the melting point (MP) of tungsten and the boiling point (BP) of the other material has the pros and cons. It is effective for the decrease of the anode erosion when the anode heat energy is relatively weak, while it can promote the splashing erosion when the liquid tungsten layer has been formed on the anode tip. These results are beneficial for the optimal design of the electrode system in circuit breakers.