Marek Pokorný

Marek Pokorný

Auto-generated profile, based on publicly available information

Marek Pokorný

Fire Laboratory, University Centre for Energy Efficient Buildings of Czech Technical University in Prague, Třinecká 1024, 273 43 Buštěhrad, Czech Republic

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 March 2014 in Earth Surface Processes and Landforms
Verified
Journal Article
Open access
PDF file
MPM. L. von Pokorny
M. L. von Pokorny
SHS. Horender
S. Horender
Two computational methods to measure particle rotations from shadow images of sand particles saltating in a wind tunnel are presented. One method calculates the maximum of the cross‐correlations through multiple angular rotations of an imaged particle. The second method polar transforms both images and then calculates the correlation coefficient for multiple pixel displacements in the θ axis, corresponding to particle rotations. The results from both methods were analysed as a function of height above sand bed (3.7–33.4 mm) and particle size (0.32–0.93 mm equivalent mean diameter). Our results indicate little evidence that particle rotation speeds depend on either their size or height above the sand bed. Though similar results were obtained from both methods, there existed different advantages and disadvantages between the methods. Erroneous results likely arose from particles that were inadequately described by a 2‐D rotation axis, or from poorly imaged particles. At a wind tunnel speed of about 12 m/s, most particles rotated at around 300–400 rev/s. Negative rotations were also found, and their proportion was approximately 15% within the total range of −450 to 850 rev/s. The ratio of displacement kinetic energy to rotation energy was compared across the various groups and had values between 15 and 40. The quotient showed little dependence on height, though decreased with increasing particle size. Wider applicability of the measurement methodology to study snow particle rotation is also discussed. Copyright © 2014 John Wiley & Sons, Ltd.

30 May 2021 in Fire Technology
Verified
Journal Article
Closed access
PDF file
RFRichard Fürst
Richard Fürst
TVTomáš Vlach
Tomáš Vlach
MPMarek Pokorný
Marek Pokorný
MÓMózer
Mózer
VLVladimír
Vladimír
VMVladimír Mózer
Vladimír Mózer

22 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
RFRichard Fürst
Richard Fürst
EFEliška Fürst
Eliška Fürst
TVTomáš Vlach
Tomáš Vlach
JŘJakub Řepka
Jakub Řepka
MPMarek Pokorný
Marek Pokorný
VMVladimír Mózer
Vladimír Mózer
Textile-reinforced concrete (TRC) is a material consisting of high-performance concrete (HPC) and tensile reinforcement comprised of carbon roving with epoxy resin matrix. However, the problem of low epoxy resin resistance at higher temperatures persists. In this work, an alternative to the epoxy resin matrix, a non-combustible cement suspension (cement milk) which has proven stability at elevated temperatures, was evaluated. In the first part of the work, microscopic research was carried out to determine the distribution of particle sizes in the cement suspension. Subsequently, five series of plate samples differing in the type of cement and the method of textile reinforcement saturation were designed and prepared. Mechanical experiments (four-point bending tests) were carried out to verify the properties of each sample type. It was found that the highest efficiency of carbon roving saturation was achieved by using finer ground cement (CEM 52.5) and the pressure saturation method. Moreover, this solution also exhibited the best results in the four-point bending test. Finally, the use of CEM 52.5 in the cement matrix appears to be a feasible variant for TRC constructions that could overcome problems with its low temperature resistance.

1 June 2019 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
MPM Pokorný
M Pokorný
MEM Eliáš
M Eliáš
FKF Kregl
F Kregl
Water mist extinguishing systems are becoming more popular due to their much higher fire-fighting efficiency at lower water consumption compared to conventional sprinklers. The article focuses on the possibility of further utilization in a form of cooling structures and presents the results of a research in the area of low-pressure water mist and the development of a new low-pressure water mist cooling system. It also introduces a new possible direction for application of cooling steel structures or their surroundings in order to increase fire resistance of steel structures. To verify the cooling effects of low-pressure water mist, a large-scale fire test with a model of steel roof construction was carried out in a room with dimensions of 4.0 × 4.0 × 2.0 m. The fire test was conducted in two scenarios. The first scenario is a reference test without application of water mist, where temperatures of the burning room and steel structures are monitored. Compared to the first scenario, the second scenario includes the use of low-pressure water mist protection of the steel structure model at the time of full fire development.