22 April 2016 in Langmuir
The influence of particle adsorption on liquid/liquid interfacial tension is not well understood, and much previous research has suggested conflicting behaviors. In this paper we investigate the surface activity and adsorption kinetics of charge stabilised and pH-responsive polymer stabilised colloids at oil/water interfaces using two tensiometry techniques; i) pendant drop and ii) microtensiometer. We found, using both techniques, that charge stabilised particles had little or no influence on the (dynamic) interfacial tension; although, dense silica particles affected the ‘apparent’ measured tension in the pendent drop, due to gravity driven elongation of the droplet profile. Nevertheless, this apparent change additionally allowed the study of adsorption kinetics, which was related qualitatively between particle systems by estimated diffusion coefficients. Significant and real interfacial tension responses were measured using ~53 nm core-shell latex particles with a pH-responsive polymer stabilizer of poly(methylmethacrylate) -b- poly(2-(dimethylamino)ethylmethacrylate) (pMMA-b-pDMAEMA) diblock copolymer. At pH 2, where the polymer is strongly charged, behavior was similar to that of the bare charge-stabilised particles, showing little change in the interfacial tension. At pH 10, where the polymer is discharged and poorly soluble in water, a significant decrease in the measured interfacial tension commensurate with strong adsorption at the oil-water interface was seen, which was similar in magnitude to the surface activity of the free polymer. These results were both confirmed through droplet profile and microtensiometry experiments. Dilational elasticity measurements were also performed by oscillation of the droplet; again, changes in interfacial tension with droplet oscillation were only seen with the responsive particles at pH 10. Frequency sweeps were performed to ascertain the dilational elasticity modulus, with measured values being significantly higher than previously reported for nanoparticle and surfactant systems, and similar in magnitude to protein stabilized droplets.
15 February 2010 in Soft Matter
There is currently significant interest in particle-stabilized emulsions for a variety of applications and as precursors to other materials such as microcapsules or colloidosomes. A prerequisite for many applications is the ability to produce stable droplets with a well-controlled size. The preparation of oil-in-water (o/w) emulsions stabilized by silica colloids has been demonstrated here using membrane emulsification techniques. Emulsions were produced using both a cross-flow membrane device and a rotating membrane reactor. Under the correct conditions, highly stable emulsions with very narrow droplet size distributions can be produced. Investigations into the effects of changing the cross-flow shear rate at a fixed droplet production rate illustrate the fine control over mean droplet size that is possible with these emulsification techniques. Evidence for the importance of particle adsorption kinetics onto growing droplets prior to detachment from the membrane surface was obtained by varying the droplet production rate under fixed shear conditions. The presence of a critical surface coverage by the stabilizing particles to prevent droplet coalescence was clearly seen. Comparison with samples produced using conventional high-shear homogenization highlights the improved control over size distribution available from these membrane techniques.
8 December 2011 in Soft Matter
There is currently a significant interest in the production of stable emulsions using particulate emulsifiers. A key design and manufacturing challenge in such systems is the production of emulsions with controlled droplet sizes and narrow polydispersity; one candidate production technique is membrane emulsification. In this study we demonstrate that under optimal conditions, highly stable near monodisperse tricaprylin droplets stabilised with 800 nm silica colloids can be achieved using Rotating Membrane Emulsification (RME). We report the influence of various mechanical and chemical parameters on the droplet sizes and size distributions. The optimal conditions for highly stable emulsions with narrow size distributions using the RME approach are described. Investigating the rotational speed and particle concentration in particular highlights the importance of particle adsorption kinetics onto a growing droplet on the detachment of that droplet from the membrane. The data clearly show that if the particles attach and adsorb to the interface before a critical droplet detachment time, stable monodisperse droplets are produced. However, if the adsorption time takes longer than this critical value, the partially stabilized droplets can coalesce and we observe a wider size distribution.
12 March 2012 in Soft Matter
In the past eight years, several examples of colloidosome microcapsules have been developed. Such microcapsules systems are offering alternative options for the encapsulation and release of active ingredients on the basis of the size exclusion properties of their colloidal membranes. Here, we use latex particles sterically stabilised with a responsive polymer as the building blocks for the colloidosome microcapsule membranes and demonstrate that the designed microcapsules can be used as a pH-responsive system to control the release of water-soluble species on the basis of size exclusion. For their manufacture, an oil-in-water emulsion is prepared using the latex particles to stabilise the emulsion. The latex particles are reacted in situ, using an oil-soluble cross-linker, to permanently link the steric polymers on adjacent particles, thus producing a robust capsule shell. The oil core is subsequently removed from the encapsulated emulsion droplets using a solvent exchange mechanism to give water-containing microcapsules suspended in water. As the oil is removed, the microcapsules initially collapse on themselves but they can be easily re-swollen to their initial spherical shape using a combination of polymer expansion within the membrane and induced chemical potential differences between the microcapsule cores and the bulk. We show here that the responsive polymer on the surface of the constituent particles within the monolayer forming the microcapsule membrane can be induced to expand and contract through changes in the dispersion pH as a result of its weakly basic nature. Using a fluorescently-labelled dextran molecule, we demonstrate its successful uptake within the core of the microcapsules at low pH where the capsule membrane is expanded and the pore size is maximised. Altering the pH to higher values results in the contraction of the membrane and closing of the surface pores; under these conditions we show that the dextran can be successfully retained within the microcapsules. Finally, we demonstrate the pH-dependent release of the labelled sugar by readjusting the pH to acidic conditions.
9 July 2020 in Crystal Growth & Design
25 August 2017 in Langmuir