This study presents a design of a 94-GHz high-performance and highly compact frequency-modulated continuous-wave radar sensor. In this sensor, an $X$ -band CMOS-based all-digital phase-locked loop chip, $W$ -band SiGe-based transceiver monolithic microwave integrated circuit (MMIC), and $W$ -band GaN-based MMIC power amplifier (PA) are heterogeneously integrated (HI). Each part of the 130-nm bipolar complementary metal-oxide-semiconductor (BiCMOS) SiGe-based transceiver MMIC is designed to include a low-noise amplifier, PA, octupler, mixer, and lange coupler. The fabrication process of our in-house silicon-based MEMS photosensitive composite film is developed to provide very high-density integration and very low insertion loss of interconnections between chips. The HI front end of the radar sensor is measured on-wafer with a high output power of 22 dBm. Moreover, a low double-sideband noise figure (NF) of 10.2 dB is obtained. Bonding–substrate integrated waveguide (SIW)–WG transitions between the heterogeneously integrated front end and the antenna are specially designed and verified. A 2.3-dB degradation is observed, where 19.7 dBm is measured at the transmitter WG WR-10-flange. Thus, the sensor offers a 55-dB dynamic range at a 2-m position with an expectation of a long-distance target-detection range. The radar sensor has an 11.7-cm range resolution and is only $60\times 40\times $ 8 mm 3 in size, with a weight of only 78 g.
7 November 2023 in IEEE Transactions on Microwave Theory and Techniques
This article presents a novel 30.5-dBm output power 1 transmitter and 2 receivers (1T2R) heterogeneously integrated (HI) phased-array frequency-modulated continuous-wave (FMCW) radar transceiver using local oscillator (LO) phase shifting (PS). Two $X$ -band GaAs-based 6-bit PSs are designed and placed at the LO path. Two $W$ -band GaN-based power amplifiers (PAs) are proposed, amplifying the FMCW signals with 30.5 dBm at output. The antenna in package (AiP) is designed and fabricated in a high-resistivity silicon wafer by combining through silicon ring-trench and artificial magnetic conductor (AMC), where the 1 $\times$ 4 antenna array has a high radiation efficiency (70%), a broadband (12%), and a high gain (11.8 dBi) in the $W$ -band. Two $W$ -band SiGe-based transceiver systems on a chip, GaN-based PAs, AMC-based AiPs, and two $X$ -band GaAs PSs are HI with a transceiver size of 31 $\times$ 17 mm $^{{2}}$ by using our in-house silicon-based MEMS photosensitive composite film given the advantages of high-density integration and fabrication accuracy. The HI radar application is measured with an effective isotropic radiated power of 41 dBm with a measured 2 cm range resolution. The beam scanning performance is also measured and presented using three corner reflectors located at different azimuths. Simulated and measured beamforming results show good agreement. The HI radar sensor has a size of 70 $\times$ 70 mm $^{{2}}$ with a weight of only 200 g.
19 February 2024 in IEEE Transactions on Microwave Theory and Techniques
This article presents the design of a CMOS-based voltage-controlled oscillator (VCO) operating in both $V$ -and $W$ -bands by fully utilizing the harmonics in Class-F $_{23}$ tank. An auxiliary common mode (CM) resonance is introduced to Class-F $_{23}$ structure via a transformer for CM resonance expansion. This transformer serves dual functions, also generating the second harmonic output, thereby enhancing the area efficiency. The proposed CM resonance expansion suppresses the flicker noise upconversion in a widehband without manual harmonic tuning. A Class-F $_{23}$ VCO without CM expansion is designed and fabricated for comparison. Besides, the challenges in high-frequency harmonic extraction are highlighted and addressed. The proposed VCO is fabricated using 40-nm CMOS technology. The frequency can cover from 69.92 to 73.84 GHz and from 104.88 to 110.75 GHz with tuning ranges of 5.7%. The measured $V$ -and $W$ -band phase noises (PNs) are $-$ 102.5 and $-$ 92.35 dBc/Hz at 1-MHz offset with figures of merit of $-$ 182.5 and $-$ 176 dBc/Hz, respectively. The power consumption is 44 mW in an area of 0.36 mm $^{2}$ .
20 March 2025 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This study proposes the design, fabrication, and testing of a three-dimensional (3-D) integrated transmitter operating at W-band. Detailed analyses of the performance variations before and after packaging of the phase shifter (PS) and power amplifier (PA) are provided, along with specific design processes. The circuit and packaging of the PS and PA are co-designed to maintain their performance and minimize proximity effects during 3-D integration at millimeter-wave frequencies. The PS achieves a -6.4 dB loss at 100 GHz, with a phase root mean square (RMS) error of 1.11° and a gain RMS error of 0.855 dB. The PA achieves a maximum gain of 19.5 dB at 103 GHz, with a bandwidth from 99.2 GHz to 106.7 GHz and a saturated output power of 13 dBm. Both the PS and PA are individually packaged using proprietary silicon-based MEMS through-silicon-trench technology and multi-layer photosensitive composite film. Finally, a 3-D integration of the transmitter system is realized using micro-bumps based on 3-D transition structures.
4 April 2025 in IEEE Microwave and Wireless Technology Letters
This letter proposes a novel implementation for W-band Class-F23 voltage-controlled oscillator (VCO). The proposed transformer exhibits magnetic coupling in both differential mode (DM) and common mode (CM), features a high Q-factor in DM, and simultaneously provides implicit CM expansion. Therefore, low-phase noise and a low-flicker noise corner are achieved in this design. Harmonic control in the proposed transformer is explicitly demonstrated. The proposed VCO is fabricated using 65-nm CMOS technology. The frequency ranges from 76 to 87 GHz, with a tuning range of 12%. The measured phase noise is −102.5 dBc/Hz, with figures of merit of 183 dBc/Hz at 1-MHz offset. The power consumption of the VCO is 46 mW in an area of 0.144 mm2.
11 February 2025 in IEEE Transactions on Microwave Theory and Techniques
This article presents the design and packaging of a 3-D integrated CMOS transmitter comprising a Class-F voltage-controlled oscillator (VCO) and a W-band power amplifier (PA). A detailed 3-D packaging methodology is introduced to highlight the advantages of the package. The effect of packaging on CMOS on-chip passive components is analyzed, followed by the modeling of packaged on-chip passive components, which is validated through measurements. A co-design methodology for circuit design and packaging is proposed, incorporating the effects of packaging into the design process to optimize the performance of the packaged chip. A VCO and PA, fabricated using 40-nm CMOS technology, are packaged with a silicon-based MEMS photoreceptor composite film, enabling 3-D integration with minimal interconnect loss. The packaged VCO achieves a tuning range of 104–110 GHz and a phase noise (PN) of -90 dBc/Hz at 1 MHz. The PA exhibits a saturated output power of 13.24 dBm. After 3-D packaging, the VCO chip is integrated atop the PA chip with an interconnect loss of only 0.2 dB. The complete 3-D transmitter system delivers an output power of up to 8 dBm within a core area of just 0.63 mm2.