27 October 2016 in Plasma Physics and Controlled Fusion
TTthe EUROfusion MST1 Team
+20
A comparison of the ASDEX Upgrade 3-strap ICRF antenna data with the linear electro-magnetic TOPICA calculations is presented. The comparison substantiates a reduction of the local electric field at the radially protruding plasma-facing elements of the antenna as a relevant approach for minimizing tungsten (W) sputtering in conditions when the slow wave is strongly evanescent. The measured reaction of the time-averaged RF current at the antenna limiters to the antenna feeding variations is less sensitive than predicted by the calculations. This is likely to have been caused by temporal and spatial fluctuations in the 3D plasma density distribution affected by local non-linear interactions. The 3-strap antenna with the W-coated limiters produces drastically less W sputtering compared to the W-coated 2-strap antennas. This is consistent with the non-linear asymptotic SSWICH-SW calculations for RF sheaths.
1 April 2019 in Electrochimica Acta
30 October 2019 in Nuclear Fusion
1 January 2019 in Nuclear Materials and Energy
2 March 2016 in Nuclear Fusion
Experiments have been performed under the coordination of the International Tokamak Physics Activity (ITPA) on several tokamaks, including ASDEX Upgrade (AUG), JET and DIII-D, to characterize the increased Ion cyclotron range of frequency (ICRF) antenna loading achieved by optimizing the position of gas injection relative to the RF antennas. On DIII-D, AUG and JET (with the ITER-Like Wall) a 50% increase in the antenna loading was observed when injecting deuterium in ELMy H-mode plasmas using mid-plane inlets close to the powered antennas instead of divertor injection and, with smaller improvement when using gas inlets located at the top of the machine. The gas injection rate required for such improvements (~0.7 × 1022 el s−1 in AUG, ~1.0 × 1022 el s−1 in JET) is compatible with the use of this technique to optimize ICRF heating during the development of plasma scenarios and no degradation of confinement was observed when using the mid-plane or top inlets compared with divertor valves. An increase in the scrape-off layer (SOL) density was measured when switching gas injection from divertor to outer mid-plane or top. On JET and DIII-D, the measured SOL density increase when using main chamber puffing is consistent with the antenna coupling resistance increase provided that the distance between the measurement lines of sight and the injection location is taken into account. Optimized gas injection was also found to be beneficial for reducing tungsten (W) sputtering at the AUG antenna limiters, and also to reduce slightly the W and nickel (Ni) content in JET plasmas. Modeling the specific effects of divertor/top/mid-plane injection on the outer mid-plane density was carried out using both the EDGE2D-EIRENE and EMC3-EIRENE plasma boundary code packages; simulations indeed indicate that outer mid-plane gas injection maximizes the density in the mid-plane close to the injection point with qualitative agreement with the AUG SOL density measurements for EMC3-EIRENE. Field line tracing for ITER in the 15 MA Q DT = 10 reference scenario indicates that the planned gas injection system could be used to tailor the density in front the antennas. Benchmarking of EMC3-EIRENE against AUG and JET data is planned as a first step towards the ITER SOL modelling required to quantify the effect of gas injection on the SOL density in front of the antennas.
5 February 2016 in Nuclear Fusion
In recent experiments, a local gas puff was found to be an effective way to tailor the scrape-off layer (SOL) density and improve the ion cyclotron range of frequency (ICRF) power coupling in tokamaks. In order to quantitatively reproduce these experiments, to understand the corresponding physics and to optimize the gas valve positions and rates, simulations were carried out with the 3D edge plasma transport code EMC3-EIRENE in ASDEX Upgrade. An inter-ELM phase of an H-mode discharge with a moderate gas puff rate (1.2 × 1022 electrons s−1) is used in our simulations. We simulated cases with gas puff in the lower divertor, the outer mid-plane and the top of the machine while keeping other conditions the same. Compared with the lower divertor gas puff, the outer mid-plane gas puff can increase the local density in front of the antennas most effectively, while a toroidally uniform but significantly smaller enhancement is found for the top gas puff. Good agreement between our simulations and experiments is obtained. With further simulations, the mechanisms of SOL density tailoring via local gas puffing and the strategies of gas puff optimization are discussed in the paper.