Javier Serrano-Pérez

Javier Serrano-Pérez

Auto-generated profile, based on publicly available information

Javier Serrano-Pérez

Universidad Politécnica del Valle de México

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2021 in Applied Soft Computing
Verified
Journal Article
Closed access
OSOmar Serrano-Perez
Omar Serrano-Perez
Miguel Gabriel CervantesMiguel Gabriel Cervantes
Miguel Gabriel Cervantes
Alejandro Rodríguez-MolinaAlejandro Rodríguez-Molina
Alejandro Rodríguez-Molina
JSJavier Serrano-Pérez
Javier Serrano-Pérez

15 December 2023 in Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI
Verified
Journal Article
Open access
PDF file
JSJavier Serrano-Pérez
Javier Serrano-Pérez
IPInocencia Pacheco-Chávez
Inocencia Pacheco-Chávez
MCMónica Araceli Camacho-González
Mónica Araceli Camacho-González
OSOmar Serrano-Perez
Omar Serrano-Perez
Jaime Pacheco MartínezJaime Pacheco Martínez
Jaime Pacheco Martínez
This work presents the design and construction of a dip-coater revolver machine to manufacture homogeneous coatings on metallic substrates. The material used for the fabrication of the machine structure was 6061-T6 aluminum. A Nema 23 stepper motor of 4.2 A and 24 V with a speed reducer with a 10:1 ratio that can provide an angular velocity ω between 1-80 rpm was used for the motion system. DC linear actuator was used for the immersion process, which operates in the range of 12-24 V at 7 A, with a stroke length of 50 mm and a maximum linear speed of 12 mm/s. For the coating tests, SayerLack® black and white base paint was used on 6061-T6 aluminum substrates and 304 stainless steel substrates. Finally, the mathematical model and the simulation of an automatic PID control system were carried out to automate the coating manufacturing process.

1 January 2023 in Ingeniería Investigación y Tecnología
Verified
Journal Article
Closed access
JPJavier Serrano Pérez
Javier Serrano Pérez
In this research, a low-speed impact numerical simulation has been performed on a 6063-T6 Aluminum alloy bumper welded by MIEA technique using ANSYS® LS-DYNA® Workbench™ 19.2, according to the requirements of the Federal Motor Vehicle Safety Standards and Regulations. For the numerical simulation, mechanical properties were obtained from quasi-static tensile tests in 6063-T6 aluminum alloy joints, these joints were manufactured using the MIEA (modified indirect electric arc) technique and a MIG welding process and post-weld heat treatment (PWHT). For the numerical impact simulation, the following parameters have been used: mass of the impactor of 1000 kg, speed of the impactor 4 km/hr and material of the impactor AISI 4130 steel. The simulation study showed that aluminum alloy joints used in bumper beam has excellent mechanical strength under low-speed impact conditions. Among the mechanical properties that have been recovered due to PWHT are the following: it was possible to harden the fusion zone, that is, there was an increase in hardness values from 80 HV0.1 to 98 HV0.1, the heat affected zone was eliminated, obtaining hardness values of approximately 110 HV0.1, a recovery in yield strength (59%) was observed, that is, in welding condition (170 MPa) and welding condition plus PWHT (270 MPa). In terms of tensile strength, a recovery (42%) was observed, going from welding condition (214 MPa) and welding condition plus PWHT (304 MPa). Tensile strength also had an increase ranging from 214 MPa to 304 MPa. This represents an increase of 42 pct. Finally, the simulation showed that the welding zone on the bumper has very good resistance to low speed impact since no permanent deformations were observed, that is, after the impact the bumper returns to its initial position.