18 April 2005 in IEEE Transactions on Microwave Theory and Techniques
In this paper, a new approach for the development of planar metamaterial structures is developed. For this purpose, split-ring resonators (SRRs) and complementary split-ring resonators (CSRRs) coupled to planar transmission lines are investigated. The electromagnetic behavior of these elements, as well as their coupling to the host transmission line, are studied, and analytical equivalent-circuit models are proposed for the isolated and coupled SRRs/CSRRs. From these models, the stopband/passband characteristics of the analyzed SRR/CSRR loaded transmission lines are derived. It is shown that, in the long wavelength limit, these stopbands/passbands can be interpreted as due to the presence of negative/positive values for the effective /spl epsiv/ and /spl mu/ of the line. The proposed analysis is of interest in the design of compact microwave devices based on the metamaterial concept.
1 November 2004 in Physical Review Letters
The electromagnetic theory of diffraction and the Babinet principle are applied to the design of artificial metasurfaces and metamaterials. A new particle, the complementary split rings resonator, is proposed for the design of metasurfaces with high frequency selectivity and planar metamaterials with a negative dielectric permittivity. Applications in the fields of frequency selective surfaces and polarizers, as well as in microwave antennas and filter design, can be envisaged. The tunability of all these devices by an applied dc voltage is also achievable if these particles are etched on the appropriate substrate.
1 September 2001 in IEEE Transactions on Microwave Theory and Techniques
In this paper, we present a new parallel-coupled-line microstrip bandpass filter with suppressed spurious passband. Using a continuous perturbation of the width of the coupled lines following a sinusoidal law, the wave impedance is modulated so that the harmonic passband of the filter is rejected while the desired passband response is maintained virtually unaltered. This strip-width perturbation does not require the filter parameters to be recalculated and, this way, the classical design methodology for coupled-line microstrip filters can still be used. At the same time, the fabrication of the resulting filter layout does not involve more difficulties than those for typical coupled-line microstrip filters. To test this novel technique, 3rd-order Butterworth bandpass filters have been designed at 2.5 GHz, with a 10% fractional bandwidth and different values of the perturbation amplitude. It is shown that for a 47.5 % sinusoidal variation of the nominal strip width, a harmonic rejection of more than 40 dB is achieved in measurement while the passband at 2.5 GHz is almost unaltered.
13 June 2005 in IEEE Transactions on Microwave Theory and Techniques
The main aim of this paper is to demonstrate the potentiality of sub-wavelength resonators, namely, split-ring resonators, complementary split-ring resonators, and related structures to the suppression of undesired spurious bands in microwave filters, a key aspect to improve their rejection bandwidths. The main relevant characteristics of the cited resonators are their dimensions (which can be much smaller than signal wavelength at resonance) and their high-Q factor. This allows us to design stopband structures with significant rejection levels, few stages, and small dimensions, which can be integrated within the filter active region. By this means, no extra area is added to the device, while the passband of interest is virtually unaltered. A wide variety of bandpass filters, implemented in both coplanar-waveguide and microstrip technologies, have been designed and fabricated by the authors. The characterization of these devices points out the efficiency of the proposed approach to improve filter responses with harmonic rejection levels near 40 dB in some cases. It is also important to highlight that the conventional design methodology for the filters holds. For certain configurations, the presence of the resonators slightly lowers the phase velocity at the frequencies of interest with the added advantage of some level of reduction in device dimensions.
24 August 2004 in IEEE Microwave and Wireless Components Letters
In this letter, spurious passband suppression in microstrip coupled line band pass filters by means of split ring resonators (SRRs) is demonstrated for the first time. By etching SRRs in the upper substrate side, in close proximity to conductor strip, strong magnetic coupling between line and rings arises at the resonant frequency of SRRs. This inhibits signal propagation in the vicinity of that frequency, allowing the rejection of undesired passbands by properly tuning SRRs. To test this novel technique, we have designed and fabricated two different SSRs-based filters. In one case, the rings have been designed to suppress only the first spurious band, and SRRs have been etched at both sides of the 50-/spl Omega/ access lines. For the other prototype, SRRs have been etched on the active device region (i.e., surrounding the parallel coupled lines) and have been tuned to eliminate the first and second undesired bands. The measured frequency responses for these devices confirm the efficiency of this technique to suppress frequency parasitics, with rejection levels near 40 dBs, leaving the passband unaltered. Since SRRs are small particles (with sub-wavelength dimensions at the resonant frequency), this approach does not add extra area to the final layouts. Moreover, the conventional design methodology of the filters holds.
8 November 2004 in IEEE Microwave and Wireless Components Letters
A method to achieve the rejection of multiple spurious passbands in parallel-coupled-line microstrip bandpass filters is proposed. As it was previously demonstrated by the authors, using a continuous perturbation of the width of the coupled-lines following a sinusoidal law, the wave impedance can be modulated so that the first undesired harmonic passband of the filter is rejected, while the desired passband is maintained virtually unaltered. In this letter, the scope of the method is extended to reject multiple spurious passbands by employing different periods in each coupled-line section tuned to the different bands to be rejected. Simulated and measured data show that for an order-seven bandpass filter prototype, a rejection level exceeding 30 dB is obtained in the first four spurious passbands, while the desired pass-band is kept almost unaltered.