Yujie Yang

Yujie Yang

Auto-generated profile, based on publicly available information

Yujie Yang

School of Microelectronics, University of Science and Technology of China, Hefei, China

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2019 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
DXDongcheng Xie
Dongcheng Xie
DCDongliang Chen
Dongliang Chen
SPShufeng Peng
Shufeng Peng
YYYujie Yang
Yujie Yang
LXLei Xu
Lei Xu
FWFeng Wu
Feng Wu
This letter, for the first time, reports a novel metal oxide semiconductor (MOS) gas sensor based on a single cantilever. The extremely brief Platinum microheater without any coil, is on a 10 lm wide cantilever, which shows very low static power consumption and fast heating response. Sensors were fabricated on a 4 inch Si wafer using typical micro-electro-mechanical system (MEMS) process, and SnO2 was chosen as the sensing material. Test results indicate that the static power consumption is only 2.96 mW. With this applied power, the sensor can reach 400 °C and the heating-up time is just 260 μs. Both of them are enormously improved, comparing with MEMS MOS gas sensors with suspended membrane supported by slender beams. The sensor shows a good linear characteristic to 0-10 ppm ethanol. Moreover, due to the single cantilever structure, 10 sensors can be fabricated inside a die of 1 mm2, improving the integration by an order of magnitude.

15 March 2023 in IEEE Sensors Journal
Verified
Journal Article
Closed access
RLRuichen Liu
Ruichen Liu
CXChong Xing
Chong Xing
DXDongcheng Xie
Dongcheng Xie
YYYujie Yang
Yujie Yang
Muhammad MustafaMuhammad Mustafa
Muhammad Mustafa
FWFeng Wu
Feng Wu
This paper proposes a SnO2-based low-power quadrilateral gas sensor, which can realize different responses by self-temperature modulation using a single layer electrode. Four detection channels are located on four edges and are integrated with a quadrilateral micro-heater to constitute the completed sensor. Under the premise of ensuring good electrical insulation, the heater and the detection electrodes are designed in parallel on the same layer, eliminating the need for the isolation layer and subsequent dry etching steps to expose the pad. This scheme can greatly simplify the fabrication process and save manufacturing costs. On top of that, temperature modulation is realized by designing the gradational width of the microheater metal line on the four edges to achieve different responses to gases. Six types of food-related gases (trimethylamine, ethanol, hydrogen sulfide, ammonia, ethyl acetate, and formaldehyde) were tested, and the four channels of the sensor show different performances to these stimuli, which can be utilized for gas identification. Moreover, six food species were also tested, showing that the sensor can efficiently differentiate the fruit, vegetables, and meats.

20 August 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
YZYan Zhang
Yan Zhang
DXDongcheng Xie
Dongcheng Xie
YYYujie Yang
Yujie Yang
CXChong Xing
Chong Xing
DCDongliang Chen
Dongliang Chen
LXLei Xu
Lei Xu
In this paper, a high heat transfer efficiency MEMS thermal conductivity gas sensor based on three suspended bridges is demonstrated. The sensor is composed of three platinum thermistors of which one is as the heater element and the other two are as the temperature-sensing elements. The heater provides a stable heat source, and the temperature-sensing elements reflect the gas signal. To improve the temperature detection ability of the temperature-sensing elements, the heater is designed into a serpentine-shaped structure, and the temperature-measuring elements are also adapted to a serpentine shape. In addition, the temperature-measuring elements are close enough to the heater to reduce the heat transfer distance and improve the heat transfer efficiency. Simulations and experiments compared two complementary structures of suspension bridge gas sensors including a shuttle-shaped heater (Design 1) and a dumbbell-shaped heater (Design 2). The results show that the sensor of Design 2 has higher heat transfer efficiency and higher sensitivity to hydrogen, and exhibits a low detection limit of 0.2%. Furthermore, the gas sensor realizes excellent reproducibility for 2% Hydrogen in long-term tests.

25 November 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
YYYujie Yang
Yujie Yang
DXDongcheng Xie
Dongcheng Xie
DCDongliang Chen
Dongliang Chen
LGLiang Geng
Liang Geng
YZYan Zhang
Yan Zhang
FWFeng Wu
Feng Wu
This article reports for the first time a quadrilateral MEMS MOx (metal oxide) gas sensor cell with four different sensitive materials based on complete semiconductor process. In order to improve the strength, symmetry of temperature distribution, and thermal stability of the structure, the design path of the Pt heater extends to the substrate along the four supporting beams so that the joule heat generated and heat conduction in the core area are symmetrical. Four pairs of detection electrodes and micro-heater are designed on the same layer and arranged in parallel, thus the process steps are simplified and the overlapping and stacking of metals can be avoided. Each pair of detection electrodes corresponds to a type of patterned sensing material film. The sensor cell was fabricated using typical 4-inch MEMS process and four kinds of sensing materials (SnO 2 /Au, SnO2, In 2 O 3 /Au, and ZnO/Au) were completed by four times of sputtering process and patterned through UV lithography and lift-off, realizing the semiconductor process of the entire sensor cell. Five gases (ethanol, ethyl acetate, trimethylamine, ammonia, and hydrogen sulfide) were tested to verify the performance of the sensor cell, and the results show that the sensor cell have differential responses to the test gases. Furthermore, the k-nearest neighbor (KNN) pattern algorithm is used to distinguish the five gases with an accuracy of 99.33%. The sensor cell is promising in gas identification applications.

21 March 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
LGLiang Geng
Liang Geng
YYYujie Yang
Yujie Yang
DCDongliang Chen
Dongliang Chen
DXDongcheng Xie
Dongcheng Xie
CXChong Xing
Chong Xing
FWFeng Wu
Feng Wu
This paper presents a novel 1280-channel three-dimensional neural microelectrode array with a complementary wedge-shaped interface. The microelectrode array consists of five 256-channel neural microelectrode chips, which are precisely stacked in three dimensions. The bonding interface between the MEMS neural microelectrode and the FPC (Flexible Printed Circuit) comprises a set of complementary wedge-shaped bonding interfaces that exhibit mirror symmetry to each other. These interfaces are encapsulated together to form a complete sensor using the ACF (Anisotropic Conductive Film) thermocompression bonding process. This bonding interface eliminates the need for any post-processing on the bonding pads, ensuring excellent consistency and achieving 100% bonding efficiency, while facilitating high-density microelectrode integration. The neural microelectrode chip adopts a composite metal layer structural design, which integrates 256 recording microelectrodes in a 1.33 mm 2 area. This design reduces the width of the needle beam while maintaining the density of the recording electrodes. Characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry, microelectrodes modified with electroplated gold exhibited a significant reduction in AC impedance from 1 MΩ to 10 KΩ at 1KHz, demonstrating enhanced capacitive properties with improved charge storage capacity and charge transfer efficiency.

16 July 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
DCDongliang Chen
Dongliang Chen
DXDongcheng Xie
Dongcheng Xie
LGLiang Geng
Liang Geng
YYYujie Yang
Yujie Yang
QWQiuju Wu
Qiuju Wu
FWFeng Wu
Feng Wu
In this paper, a programmable interface circuit for metal-oxide-semiconductors (MOS) gas sensor array is proposed. Integrated with analog and digital circuits, the interface circuit can realize sensor configuration, signal acquisition, data processing and recognition results output by embedded with timing and algorithm code. A Fully Integrated and programmable analog front end (AFE) circuit is introduced for sensor configuration, such as heating voltage generator, measuring voltage generator, and load resistor selector. A 12-bit SAR ADC supporting multiple channels is used for signal acquisition. Data processing and analysis are completed in a Cortex-M0 processor. And recognition results can be output via common digital interfaces. The programmable interface circuit is realized in Nexchip 110nm embedded flash process platform with an area of 2.53 mm × 2.73 mm. By introducing this interface circuit, an e-nose system with virtualized sixteen channels is built up based on four MOS gas sensors and applied in safety monitoring of automotive power lithium batteries. With k-nearest neighbor classification algorithm embedded in the processor, the e-nose system identified gas types of thermal runaway process and output the current state of lithium battery pack with high accuracy.