18 October 2010 in Energy & Environmental Science
Hydrogen produced from water and renewable energy could fuel a large fleet of proton-exchange-fuel-cell vehicles in the future. However, the dependence on expensive Pt-based electrocatalysts in such fuel cells remains a major obstacle for a widespread deployment of this technology. One solution to overcome this predicament is to reduce the Pt content by a factor of ten by replacing the Pt-based catalysts with non-precious metal catalysts at the oxygen-reducing cathode. Fe- and Co-based electrocatalysts for this reaction have been studied for over 50 years, but they were insufficiently active for the high efficiency and power density needed for transportation fuel cells. Recently, several breakthroughs occurred that have increased the activity and durability of non-precious metal catalysts (NPMCs), which can now be regarded as potential competitors to Pt-based catalysts. This review focuses on the new synthesis methods that have led to these breakthroughs. A modeling analysis is also conducted to analyze the improvements required from NPMC-based cathodes to match the performance of Pt-based cathodes, even at high current density. While no further breakthrough in volume-specific activity of NPMCs is required, incremental improvements of the volume-specific activity and effective protonic conductivity within the fuel-cell cathode are necessary. Regarding durability, NPMCs with the best combination of durability and activity result in ca. 3 times lower fuel cell performance than the most active NPMCs at 0.80 V. Thus, major tasks will be to combine durability with higher activity, and also improve durability at cell voltages greater than 0.60 V.
21 June 2012 in Physical Chemistry Chemical Physics
Fe-based catalytic sites for the reduction of oxygen in acidic medium have been identified by 57Fe Mössbauer spectroscopy of Fe/N/C catalysts containing 0.03 to 1.55 wt% Fe, which were prepared by impregnation of iron acetate on carbon black followed by heat-treatment in NH3 at 950 °C. Four different Fe-species were detected at all iron concentrations: three doublets assigned to molecular FeN4-like sites with their ferrous ions in a low (D1), intermediate (D2) or high (D3) spin state, and two other doublets assigned to a single Fe-species (D4 and D5) consisting of surface oxidized nitride nanoparticles (FexN, with x ≤ 2.1). A fifth Fe-species appears only in those catalysts with Fe-contents ≥0.27 wt%. It is characterized by a very broad singlet, which has been assigned to incomplete FeN4-like sites that quickly dissolve in contact with an acid. Among the five Fe-species identified in these catalysts, only D1 and D3 display catalytic activity for the oxygen reduction reaction (ORR) in the acid medium, with D3 featuring a composite structure with a protonated neighbour basic nitrogen and being by far the most active species, with an estimated turn over frequency for the ORR of 11.4 e− per site per s at 0.8 V vs. RHE. Moreover, all D1 sites and between 1/2 and 2/3 of the D3 sites are acid-resistant. A scheme for the mechanism of site formation upon heat-treatment is also proposed. This identification of the ORR-active sites in these catalysts is of crucial importance to design strategies to improve the catalytic activity and stability of these materials.
24 February 2006 in The Journal of Physical Chemistry B
12 December 2017 in Energy & Environmental Science
In this study, we explored the behavior of NC_Ar + NH3, an initially highly active catalyst for oxygen electroreduction, in H2/air fuel cells from 0.8 to 0.2 V at 80 °C and 25 °C, in order to find the causes of its instability. We discovered that the decay of the current density always involves the superposition of fast and slow first order kinetics, for which half-lives were obtained. The half-life of the fast decay was practically the same at all potentials and temperatures with a value of around 138 ± 55 min, while the half-life of the slow decay greatly varied from a minimum of ≈2400 min (40 h) to infinity. From the adsorption–desorption isotherm of NC_Ar + NH3, it was deduced that the Fe/N/C carbonaceous catalyst is characterized by interconnected open-end slit-shaped micropores, in which water (with dissolved H+ and O2) quickly flows in the fuel cells if their width is ≥0.7 nm as it has no interaction with the hydrophobic walls of the micropores. The driving force of this quick water flow is the humidified air streaming through the working cathode. Fe–N4-like active sites are thermodynamically stable in stagnant acidic conditions, but according to the Le Chatelier principle, they demetalate in the flux of water running into the micropores. This specific demetalation is the cause of the initial loss of ORR activity of NC_Ar + NH3 catalysts assigned to the fast current decay in fuel cells.
17 October 2008 in Advanced Materials
1 January 2006 in Journal of the Electrochemical Society
Fe-based catalysts for the oxygen reduction reaction (ORR) in polymer electrolyte membrane fuel cells (PEMFCs) have been prepared with commercial and developmental carbon black powders containing initially between 0 and 0.8 atom % of nitrogen. The catalysts were obtained by adsorbing 0.2 wt % Fe from iron acetate on each carbon support, which is then pyrolyzed at 900°C for 1 h in a <mml:math display="inline"><mml:mrow><mml:msub><mml:mi>NH</mml:mi><mml:mrow><mml:mn>3</mml:mn></mml:mrow></mml:msub><mml:mo>∕</mml:mo><mml:msub><mml:mi mathvariant="normal">H</mml:mi><mml:mrow><mml:mn>2</mml:mn></mml:mrow></mml:msub><mml:mo>∕</mml:mo><mml:mi>Ar</mml:mi></mml:mrow></mml:math>NH3∕H2∕Ar mixture. Under these conditions, N contents from 0 to 2.3 atom % are measured at the surface of the catalysts and increased N content leads to increased activity for the ORR. The N content correlates with the weight loss of the carbon support due to a reaction with <mml:math display="inline"><mml:mrow><mml:msub><mml:mi>NH</mml:mi><mml:mrow><mml:mn>3</mml:mn></mml:mrow></mml:msub></mml:mrow></mml:math>NH3 during pyrolysis. It was found that <mml:math display="inline"><mml:mrow><mml:msub><mml:mi>NH</mml:mi><mml:mrow><mml:mn>3</mml:mn></mml:mrow></mml:msub></mml:mrow></mml:math>NH3 reacts mainly with the disorganized carbon, leaving nitrogen at the surface of the support. The larger the amount of disorganized carbon in the pristine carbon black, the better the activity for ORR of the resulting catalyst. The most active non-noble catalyst was tested in fuel cells, where it was found that its specific activity (in A per <mml:math display="inline"><mml:mrow><mml:msup><mml:mi>cm</mml:mi><mml:mrow><mml:mn>3</mml:mn></mml:mrow></mml:msup></mml:mrow></mml:math>cm3 of electrode) is still about two orders of magnitude below the target of a non-noble catalyst for automotive applications. However, such catalysts could already compete with Pt in, e.g., methanol fuel cells because they are ORR-selective.