In this study, a Zn-doped iron oxide layer was deposited onto a microscope slide using the magnetron co-sputtering technique with direct current (DC) and radio frequency (RF) sources. We comprehensively characterized the resulting Zn-doped Fe2O3 thin layer, employing techniques such as XRD, Raman spectroscopy, UV–VIS spectrophotometry, SEM, EDX, & AFM. XRD examination showed the nanocrystalline structure in the thin layer under investigation. Based on recorded absorption data, the band gap energy value calculation resulted in a value of 2.23 eV for the thin film. Raman spectroscopy identified peaks possessing Raman shifts from 100 to 1400 cm−1. SEM investigation illustrated a consistently uniform thin film surface characteristic throughout the substrate. Additionally, the AFM study disclosed a small RMS roughness value, indicative of an unrough surface for the Zn: Fe2O3 thin layer. The Fe2O3 thin film doped with Zn employing a 30 W DC voltage demonstrated effective hydrogen sensing capability at 300 °C, achieving notable response and recovery time. This work presents a novel application of Zn-doped Fe2O3 thin films as highly sensitive and stable hydrogen sensors, tailored for high-temperature environments. The unique combination of nanocrystalline structure and Zn doping optimizes the material’s electronic properties, enhancing its responsiveness to hydrogen gas. This approach offers a scalable, cost-effective pathway for developing advanced sensor technologies suited to environmental monitoring, industrial safety, and hazardous gas detection, making it a valuable addition to the field of gas-sensing materials.
Gallium nitride (GaN) is an attractive material with a wide-direct band gap (3.4 eV) and is one of the significant III-nitride materials, with many advantageous device applications such as high electron mobility transistors, lasers, sensors, LEDs, detectors, and solar cells, and has found applications in optoelectronic devices. GaN could also be useful for industrial research in the future. Chemical vapor deposition (CVD), molecular beam epitaxy (MBE), sputter, and pulsed laser deposition (PLD) are some of the methods used to fabricate GaN thin film. In this research, a GaN thin film grown on a silicon substrate using the thermionic vacuum arc (TVA) technique has been extensively studied. Fast deposition, short production time, homogeneity, and uniform nanostructure with low roughness can be seen as some of the merits of this method. The growth of the GaN was conducted at an operating pressure of , a plasma current and for a very short period of time of 40 s. For the characterization process, scanning electron microscopy (SEM) was conducted to determine the structure and surface morphology of the material. Energy dispersive x-ray spectroscopy (EDX) was used to comprehend the elemental analysis characterization of the film. X-ray diffraction (XRD) was used to analyze the structure of the film. Raman measurements were taken to investigate the phonon modes of the material. The morphological properties of the material were analyzed in detail by atomic force microscopy (AFM).
One of important material of III-nitrides can be said to be GaN with direct-wide band gap (~ 3.4 eV) and many industrial devices such as solar cell, LED has been based on GaN thin film. In this research, we elaborately investigated growth of GaN thin film on Si(100) substrate by RF sputter technique and characterization of the film. We have successfully grown GaN thin film on Si substrate with hexagonal structure which has been confirmed by analysis of X-ray measurements. Also, we obtained structural properties of GaN film by (XRD) X-ray Diffraction measurements depending on different Argon, nitrogen and RF power values. During experiment, the value from 25sccm to 100sccm Argon gas value, the value from 0sccm to 4sccm Nitrogen gas value and from 50 watt to 125 watt RF power value has been applied. Among these values, we determined the best film in terms of crystalline structure of film. From AFM results, we attained and analyzed average roughness (Ra), maximum peak height (Rp), and maximum depth (Rv), average absolute slope of the profile (Δa)(°) of the fılms successfully. The film having the lowest roughness (Ra) has been achieved depending on different Argon, nitrogen and RF power values. Atomic Force Microscopy results confirmed that some of the films have homogeneous and uniform structure without any holes and crack; but others has voids referring impurities coming from growth process. To sum up, not only growing GaN thin film on Si substrate has been investigated, but also some of structural and morphological parameters’ optimization has been studied, analyzed and the best film was determined in view of varied Argon, nitrogen and RF power values. For future direction, optimization of GaN thin film in detail can enable us to fabricate high quality film; therefore it will helps to improving device technology.
27 January 2017 in Journal of Materials Science: Materials in Electronics