Oleg Akimov

Oleg Akimov

Auto-generated profile, based on publicly available information

Oleg Akimov

National Technical University “Kharkiv Polytechnic Institute” (Kharkiv, Ukraine)

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 April 2016 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AIAlaa Fadhil І Idan
Alaa Fadhil І Idan
OAOleg Akimov
Oleg Akimov
LGLeonid Golovko
Leonid Golovko
OGOlexiy Goncharuk
Olexiy Goncharuk
KKKateryna Kostyk
Kateryna Kostyk
The study of the influence of laser hardening conditions on the change in properties of steels

26 April 2017 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AIAlaa Fadhil І Idan
Alaa Fadhil І Idan
OAOleg Akimov
Oleg Akimov
KKKateryna Kostyk
Kateryna Kostyk
Development of new combined strengthening technologies for treatment of steel surface layer is a topical issue. Influence of conditions of combined hardening treatment on variation of properties of the surface layer of 38Cr2MoAl steel was studied. Experimental data have shown that thickness of the hardened layer of 38Cr2MoAl steel, depending on the process conditions of combined treatment, varied in the range 0.18 to 0.69 mm with the surface hardness being 10.5–12.5 GPa. Mathematical models of the hardened layer thickness and surface hardness were obtained depending on variation of velocity of the laser beam travel and duration of nitriding of steel following the combined treatment. In their structure, the models are regression equations. These regularities have practical technological significance and ensure prediction of values of the hardened layer thickness and surface hardness. Nomograms of simultaneous influence of velocity of the laser beam travel and duration of nitriding on thickness of the hardened steel layer and surface hardness were constructed. Nomograms make it possible to determine concrete conditions of hardening processing, starting from specified thickness of the hardened layer or the surface hardness of 38Cr2MoAl steel, respectively and also to solve inverse problems. This method is suitable for hardening hard-to-reach part sectios and local contact areas.

18 November 2021
Verified
Book Chapter
Closed access
PDF file
KKKateryna Kostyk
Kateryna Kostyk
VKViktoriia Kostyk
Viktoriia Kostyk
OAOleg Akimov
Oleg Akimov
KKKateryna Kamchatna-Stepanova
Kateryna Kamchatna-Stepanova
YSYurii Shyrokyi
Yurii Shyrokyi

15 September 2018 in International Journal of Engineering & Technology
Verified
Journal Article
Open access
PDF file
HDHayder Abed Dhahad
Hayder Abed Dhahad
WAWissam Hameed Alawee
Wissam Hameed Alawee
AMAndrii Marchenko
Andrii Marchenko
DKDmytro Klets
Dmytro Klets
OAOleg Akimov
Oleg Akimov
Evaluation of Power Indicators of the Automobile Engine


19 June 2017 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AMAhmed Sundus Mohammed
Ahmed Sundus Mohammed
OAOleg Akimov
Oleg Akimov
KKKateryna Kostyk
Kateryna Kostyk
We examined a technological process for receiving an iron-based alloy with a shape memory effect, substantiated the choice of chemical composition of the alloy, and selected thermal treatment modes. Research results into scale resistance revealed at heating the samples in the temperature range of 600–1000 °C, surface oxidation was not observed. In the course of experiment on corrosion resistance of the alloy, we found that the alloy is corrosion resistant and is not inclined to change the weight when exposed to 10 % solution of sulfuric acid. Study into the microstructure confirmed the existence of dispersion hardening in the alloy after the aging regimes. Diffractogram of the alloy after hardening at a temperature of 1150 °C and cooling in the open air showed a surge that corresponds to γ-Fe, therefore, the content of residual austenite in the alloy is 100 %. Research results demonstrated that the degree of shape recovery of the proposed alloy is 78–97 %. The proposed alloy is plastic enough; it may undergo hot, warm and cold deformation in the open air. We constructed mathematical models of the impact of chemical composition of the alloy on tensile strength of the alloy and the values of a shape memory effect. The iron-based alloy with a shape memory effect can be obtained both under laboratory conditions and on industrial equipment.