Tingke Wu

Tingke Wu

Auto-generated profile, based on publicly available information

Tingke Wu

School of Mechanical Engineering, Shenyang Ligong University, Shenyang 110159, China

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 October 2019 in Materials
Verified
Journal Article
Open access
PDF file
TWTingke Wu
Tingke Wu
FZFengqun Zhao
Fengqun Zhao
Haitao LuoHaitao Luo
Haitao Luo
HWHaonan Wang
Haonan Wang
YLYuxin Li
Yuxin Li
Aiming at the problems that the temperature in the welding area of friction stir welding (FSW) is difficult to measure and the joints are prone to defects. Hence, it is particularly important to study the material flow in the welding area and improve the welding quality. The temperature of the tool shoulder and the tool pin was monitored by the wireless temperature measuring system. The finite element model of friction stir welding was established and the welding conditions were numerically simulated. The flow law of material of the friction stir welding process was studied by numerical simulation. The material flow model was established by combining the microstructure analysis results, and the forming mechanism of the defects was analyzed. The results show that the temperature in the welding zone is the highest at 1300 rpm, and the temperature at the tool shoulder is significantly higher than that at the tool pin in the welding stage. When high-rotation speeds (HRS) are chosen, the material beneath the tool shoulder tends to be extruded into the pin stirred zone (PSZ) after flowing back to the advancing side. This will cause turbulence phenomenon in the advancing side of the joint, which will easily lead to the formation of welding defects. In the future, temperature monitoring methods and the flow model of material can be used to optimize the welding parameters.

28 May 2019 in Metals
Verified
Journal Article
Open access
PDF file
Haitao LuoHaitao Luo
Haitao Luo
TWTingke Wu
Tingke Wu
PWPeng Wang
Peng Wang
FZFengqun Zhao
Fengqun Zhao
HWHaonan Wang
Haonan Wang
YLYuxin Li
Yuxin Li
Friction stir welding (FSW) material flow has an important influence on weld formation. The finite element model of the FSW process was established. The axial force and the spindle torque of the welding process were collected through experiments. The feasibility of the finite element model was verified by a data comparison. The temperature field of the welding process was analyzed hierarchically. It was found that the temperature on the advancing side is about 20 °C higher than that on the retreating side near the welding seam, but that the temperature difference between the two sides of the middle and lower layers was decreased. The particle tracking technique was used to study the material flow law in different areas of the weld seam. The results showed that part of the material inside the tool pin was squeezed to the bottom of the workpiece. The material on the upper surface tends to move downward under the influence of the shoulder extrusion, while the material on the lower part moves spirally upward under the influence of the tool pin. The material flow amount of the advancing side is higher than that of the retreating side. The law of material flow reveals the possible causes of the welding defects. It was found that the abnormal flow of materials at a low rotation speed and high welding speed is prone to holes and crack defects. The forming reasons and material flow differences in different regions are studied through the microstructure of the joint cross section. The feasibility of a finite element modeling and simulation analysis is further verified.

4 February 2019 in Materials
Verified
Journal Article
Open access
PDF file
Haitao LuoHaitao Luo
Haitao Luo
TWTingke Wu
Tingke Wu
FJFu Jia
Fu Jia
WWWei Wang
Wei Wang
NCNing Chen
Ning Chen
HWHaonan Wang
Haonan Wang
According to the actual size parameters, the finite element model (FEM) of friction stir welding (FSW) was established, and the FEM was updated by experiments. The FSW of the 2A14-T6 high-strength aluminum alloy was simulated under a reasonable welding process parameter range, and the welding process parameters with good simulation effect were determined. The test was carried out under the same parameters, and the axial force of the FSW tool and temperature of the workpiece measuring point were collected. The comparison between the simulated data and the experimental data is reasonable, indicating the correctness of the FEM. The microstructure analysis of the welded joint shows that the grain size in the upper part of the weld nugget was smaller than that in the middle and lower parts, and there are obvious boundaries of grain size in each region of the joint. The hardness of the joint in the upper layer is higher than that in the middle and lower layers, and the minimum Vickers hardness value of the joint appears near the interface between the thermo-mechanically affected zone and the heat-affected zone on both sides of the weld. Tensile testing shows that the strength coefficient of the joint reaches 82.5% under this process parameter, and the sample breaks at the intersection of the material flow during stretching. After analyzing the final mechanical properties of the joint, we found that a degree of aerospace application can be achieved. Under this parameter, the welding test was carried out on the top cover of the rocket fuel tank. Firstly, melon valve welding, which is relatively difficult in welding conditions, was carried out, and a high-quality joint with good surface and no defects was obtained.