Photopolymers have been optimized as protective and decorative coating materials for decades. However, with the rise of additive manufacturing technologies, vat photopolymerization has unlocked the use of photopolymers for three-dimensional objects with new material requirements. Thus, the originally highly cross-linked, amorphous architecture of photopolymers cannot match the expectations for modern materials anymore, revealing the largely unanswered question of how diverse properties can be achieved in photopolymers. Herein, we review how microstructural features in soft matter materials should be designed and implemented to obtain high performance materials. We then translate these findings into chemical design suggestions for enhanced printable photopolymers. Based on this analysis, we have found microstructural heterogenization to be the most powerful tool to tune photopolymer performance. By combining the chemical toolbox for photopolymerization and the analytical toolbox for microstructural characterization, we examine current strategies for physical heterogenization (fillers, inkjet printing) and chemical heterogenization (semicrystalline polymers, block copolymers, interpenetrating networks, photopolymerization induced phase separation) of photopolymers and put them into a material scientific context to develop a roadmap for improving and diversifying photopolymers’ performance.
This work investigates the development of photopolymerization‐induced phase separation (PhIPS) in methacrylate‐based photopolymers. Bisphenol A ethoxylated dimethacrylate (BisEMA) was copolymerized with urethane‐based diacrylate diluted in isobornyl acrylate (UI) under UV irradiation, using diphenyl‐(2,4,6‐trimethylbenzoyl) phosphine oxide (TPO) as a photoinitiator. Optical changes in the cured copolymers were monitored in real time with a custom setup. NIR‐photorheometry, photo‐differential scanning calorimetry, dynamic mechanical analysis, scanning electron microscopy, and atomic force microscopy in both topography and phase imaging modes were employed to characterize the PhIPS effect on network development and microstructure. The correlation between the microstructure of copolymers with varying BisEMA/UI ratios and their bulk properties was studied through tensile and dynstat impact tests. Results showed that up to 20% UI enhances the elongation at break of BisEMA without compromising strength. At higher monomer/oligomer ratios, phase separation led to a strength–ductility trade‐off. The study also addresses the influence of AFM sample preparation on correlating phase imaging results to the local stiffness distribution.
We propel photopolymerizable liquid crystalline (LC) shape memory materials from solely elastomeric performance to the thermomechanical performance of tough, yielding thermosets. LC elastomers are at the forefront of smart, stimuli-responsive materials development. To apply their properties to mechanically superior thermosets, we demonstrate main-chain incorporation of high quantities of preordered LC motifs into a densely crosslinked network via thiol-ene photopolymerization to achieve a new material class hybridizing the advantages of LC elastomers and liquid crystalline networks. A terminal alkene mesogen with a robust LC phase is combined with multiple trithiol comonomers and selected based on resulting polymer crystallinities (13-37%). The bulk materials exhibit high strength, stiffness and pronounced yielding under stress with elongations around 200%. Their excellent thermomechanical properties were explained by phase separation observed in atomic force microscopy. Furthermore, we demonstrate shape memory of these materials with fast, near-perfect shape imprinting (99%) and recovery (97%) over at least 20 cycles, and their light-based 3D printing at high temperature.
Conventional photopolymers used in light-based additive manufacturing are typically brittle materials with thermoset characteristics. Here we introduce a one-step synthesis of hyperbranched polyethylene rubbers functionalized with pendant methacrylic groups and their application as tougheners of a model brittle photopolymer based on non-volatile styrene and maleimide derivatives. The rubber tougheners can be tailored to tune their compatibility with the matrix, influencing the morphology and the thermomechanical properties of the final printed resins. The resulting polymer structures were analysed by atomic force microscopy, revealing various degrees of phase separation related to the rubber molar mass and methacrylate functionalization. Further, the analysis of the prepared toughened materials revealed the ability of functionalized hyperbranched polyethylene rubbers to improve the mechanical properties significantly, while glass transition temperatures around 100 °C could be maintained. Notably, even tensile behaviour mimicking typical thermoplastic yield strain comparable to ABS was observed in one of the prepared materials. This monomer/rubber system appeared to be the most promising and was therefore selected for in-depth analysis of the curing process using photo-rheology and photo-DSC. Finally, this material was used for hot lithography and several highly detailed objects were prepared, demonstrating the good printability of this toughened material.