20 May 2020 in Journal of Microscopy
7 April 2008 in ChemMedChem
9 June 2004 in The Journal of Physical Chemistry B
4 November 2010 in Chemistry – A European Journal
A novel fluorescently labelled synthetic ionophore, based on a cyclic phosphate‐linked disaccharide (CyPLOS) backbone and decorated with four tetraethylene glycol tails carrying dansyl units, has been synthesised in 12 steps in 26 % overall yield. The key intermediate in the synthetic strategy is a novel glucoside building block, serving through its 2‐ and 3‐hydroxy groups as the anchor point for flexible tetraethylene glycol tentacles with reactive azido moieties at their ends. To test the versatility of this glucoside scaffold, it was preliminarily functionalised with a set of diverse probes—as fluorescent, redox‐active or hydrophobic tags—either by reduction of the azides followed by condensation with activated carboxylic acid derivatives, or by a direct coupling with a terminal alkyne in a CuI‐promoted 1,3‐dipolar cycloaddition. Tagging of the monomeric building block with dansyl residues allowed us to prepare a fluorescent, amphiphilic macrocycle, which was investigated for its propensity to self‐aggregate in CDCl3—studied by means of concentration‐dependent 31P NMR spectroscopy experiments—and in aqueous solution, in which combined dynamic light scattering (DLS) and small‐angle neutron scattering (SANS) measurements provided a detailed physico‐chemical analysis of the self‐assembled systems, mainly organised in the form of large vesicles. Its ion‐transport properties through phospholipid bilayers, determined by HPTS fluorescence assays, showed this compound to be more active than the previously synthesised CyPLOS congeners. Solvent‐dependent fluorescence changes for the labelled ionophore in liposome suspension established that the dansyl moieties are dispersed in environments with polarity intermediate between those of CH2Cl2 and propan‐2‐ol, suggesting that the CyPLOS tentacles infiltrate the mid‐polar region of the membranes.
1 November 2017 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
Using grazing incidence scattering methods allows for depth profiling near surface structures very efficiently Dosch (1986). In parallel, layered structures have been used as resonators to enhance the wave field Kozhevnikov et al. (2007), Khaydukov et al. (2011), Kozhevnikov et al. (2011) and Nesnidal and Walker (1996) that directly increases the scattered intensity too. Third, the combination of these methods with neutron spin echo spectroscopy allows for near surface studies of dynamics Jaksch et al. (2015) and Frielinghaus et al. (2012) that can be correlated to tribological effects on the molecular level. This field of science, the tribology, - so far - has been driven mainly by the surface force balance that measures the macroscopic response of the system (latest research employs also AFM) Raviv et al. (2003) [1], Chung et al. (2016) [2] and Mocny and Klok (2016) [3]. The progress of this method was to reach the nano-scale distances that were necessary to obtain information about the friction of the nano-structures. The proposed method of grazing incidence neutron spin echo spectroscopy gives access to much more detailed information of molecular response to confinement by one or two hard walls, and therefore would pave the way for very rich and precise tribological comparisons of theory with experiments
1 November 2020 in Review of Scientific Instruments
In neutron scattering on soft matter, an important concern is the control and stability of environmental conditions surrounding the sample. Complex sample environment setups are often expensive to fabricate or simply not achievable by conventional workshop manufacturing. We make use of state-of-the-art 3D metal-printing technology to realize a sample environment for large sample sizes, optimized for investigations on thin film samples with neutron reflectometry (NR) and grazing-incidence small-angle neutron scattering (GISANS). With the flexibility and freedom of design given by 3D metal-printing, a spherical chamber with fluidic channels inside its walls is printed from an AlSi10Mg powder via selective laser melting (SLM). The thin channels ensure a homogeneous heating of the sample environment from all directions and allow for quick temperature switches in well-equilibrated atmospheres. In order to optimize the channel layout, flow simulations were carried out and verified in temperature switching tests. The spherical, edgeless design aids the prevention of condensation inside the chamber in case of high humidity conditions. The large volume of the sample chamber allows for high flexibility in sample size and geometry. While a small-angle neutron scattering (SANS) measurement through the chamber walls reveals a strong isotropic scattering signal resulting from the evenly orientated granular structure introduced by SLM, a second SANS measurement through the windows shows no additional background originating from the chamber. Exemplary GISANS and NR measurements in time-of-flight mode are shown to prove that the chamber provides a stable, background free sample environment for the investigation of thin films.