Sea surface images have been collected to determine the percentage whitecap coverage (W) since the late 1960s. Image processing methods have changed dramatically since the beginning of whitecap studies. An automated whitecap extraction (AWE) technique has been developed at the National University of Ireland, Galway, that allows images to be analyzed for percentage whitecap coverage without the need of a human analyst. AWE analyzes digital images and determines a suitable threshold with which whitecaps can be separated from unbroken background water. By determining a threshold for each individual image, AWE is suitable for images obtained in conditions of changing ambient illumination. AWE is also suitable to process images that have been taken from both stable and nonstable platforms (such as towers and research vessels, respectively). Using techniques based on derivative analysis, AWE provides an objective method to determine an appropriate threshold for the identification of whitecaps in sea surface images without the need for a human analyst. The automated method allows large numbers of images to be analyzed in a relatively short amount of time. AWE can be used to analyze hundreds of images per individual W data point, which produces more convergent values of W.
14 September 2012 in Journal of Geophysical Research: Oceans
Air-entraining breaking waves form oceanic whitecaps and play a key role in climate regulation through air-sea bubble-mediated gas transfer, and sea spray aerosol production. The effect of varying sea surface temperature on air entrainment, subsurface bubble plume dynamics, and surface foam evolution intrinsic to oceanic whitecaps has not been well studied. By using a breaking wave analog in the laboratory over a range of water temperatures (Tw = 5°C to Tw = 30°C) and different source waters, we have examined changes in air entrainment, subsurface bubble plumes, and surface foam evolution over the course of a breaking event. For filtered seawater, air entrainment was estimated to increase by 6% between Tw = 6°C and Tw = 30°C, driven by increases of about 43% in the measured surface roughness of the plunging water sheet. After active air entrainment, the rate of loss of air through bubble degassing was more rapid at colder water temperatures within the first 0.5 s of plume evolution. Thereafter, the trend reversed and bubbles degassed more quickly in warmer water. The largest observed temperature-dependent differences in subsurface bubble distributions occurred at radii greater than about 700 μm. Temperature-dependent trends observed in the subsurface bubble plume were mirrored in the temporal evolution of the surface whitecap foam area demonstrating the intrinsic link between surface whitecap foam and the subsurface bubble plume. Differences in foam and plume characteristics due to different water sources were greater than the temperature dependencies for the filtered seawater examined.
A laboratory experiment to quantify whitecap foam decay time in the presence or absence of surface active material is presented. The investigation was carried out in the glass seawater channel at the Hydraulics Facility of Scripps Institution of Oceanography. Whitecaps were generated with focused, breaking wave packets in filtered seawater pumped from La Jolla Shores Beach with and without the addition of the surfactant Triton X-100. Concentrations of Triton X-100 (204 μg L−1) were chosen to correspond to ocean conditions of medium productivity. Whitecap foam and subsurface bubble-plume decay times were determined from digital images for a range of wave scales and wave slopes. The experiment showed that foam lifetime is variable and controlled by subsurface bubble-plume-degassing times, which are a function of wave scale and breaking wave slope. This is true whether or not surfactants are present. However, in the presence of surfactants, whitecap foam is stabilized and persists for roughly a factor of 3 times its clean seawater value. The range of foam decay times observed in the laboratory study lie within the range of values observed in an oceanic dataset obtained off Martha’s Vineyard in 2008.
5 January 2016 in Journal of Geophysical Research: Oceans
Models of the air‐sea transfer velocity of gases may be either empirical or mechanistic. Extrapolations of empirical models to an unmeasured gas or to another water temperature can be erroneous if the basis of that extrapolation is flawed. This issue is readily demonstrated for the most well‐known empirical gas transfer velocity models where the influence of bubble‐mediated transfer, which can vary between gases, is not explicitly accounted for. Mechanistic models are hindered by an incomplete knowledge of the mechanisms of air‐sea gas transfer. We describe a hybrid model that incorporates a simple mechanistic view—strictly enforcing a distinction between direct and bubble‐mediated transfer—but also uses parameterizations based on data from eddy flux measurements of dimethyl sulphide (DMS) to calibrate the model together with dual tracer results to evaluate the model. This model underpins simple algorithms that can be easily applied within schemes to calculate local, regional, or global air‐sea fluxes of gases.