In this study, we propose a long-reach aerial manipulation system with a wire-suspended device that allows the airframe to maintain its position at the desired distance away from the target. We implemented a feedback communication between the multirotor and wire-suspended device to maintain the position of the wire-suspended device directly below the multirotor while maintaining a constant distance from the target. The multirotor communicates its velocity and relative position to the wire-suspended device to control the ducted fans, whereas the wire-suspended device transmits the attitude and distance from the ground to the multirotor to control the winch. The designed controller for the ducted fans allows the wire-suspended device to behave like a long rigid robotic arm. The performance of the designed controller was verified by navigating the multirotor over stepped surfaces while the wire-suspended device was being lowered.
UAVs are one of the fastest types of robots that can be deployed in a remote environment. Unfortunately, they have a limited flight time and therefore may need to stop occasionally in an unknown, uncontrolled area. However, conventional UAVs require flat and stationary surfaces for a safe landing and take-off. Some studies on adaptive landing approach for UAVs can be found in the past, but adaptive take-off from non-flat surfaces has not been discussed for the most part, yet. In this work, we discuss the problems associated with a conventional UAV take-off from non-flat surfaces and provide a novel approach for UAV take-off from a sloped or rocking surface. We also discuss the design of a novel multitasking three-arm aerial manipulator system with parallel link mechanism and achieve the above-mentioned task. With experiments, we show that the system can provide stability for a UAV landing on a rocking surface that allows for a safe take-off.
In this study, we propose a multirotor aerial robot for high-pressure washing tasks at high altitudes. The aerial robot consists of a multirotor platform, an add-on planar translational driving system (ATD), a visual sensing system, and a high-pressure washing system. The ATD consists of three ducted fans, which can generate force in all directions on the horizontal plane. The ATD also allows the multirotor to suppress the reaction force generated by the nozzle of a high-pressure washing system and inject water accurately. In this study, we propose a method to precisely inject water by installing an ATD in the multirotor and using its driving force to suppress the reaction force and move the multirotor while keeping its posture horizontal. The semi-autonomous system was designed to allow the operator to maneuver the multirotor while maintaining a constant distance from the wall by the sensor feedback with onboard LiDAR or stereo camera. In the experiment, we succeeded in performing the high-pressure washing task in a real environment and verified that the reaction force generated from the nozzle was actually suppressed during the task.
17 October 2024 in IEEE Robotics and Automation Letters
This research proposes a passively driven perching mechanism designed to land not only on flat surface but also on various shaped objects, such as bar, plate, and spherical object, without the use of additional actuators. The perching mechanism consists of three under actuated fingers, and utilizes two passive drive mechanisms: one for landing without bending the fingers but by pinching, and another for grasping by bending the fingers to land. As a result, a lightweight apparatus capable of landing on various objects without the need for additional CPUs, motors, or batteries for driving and controlling was achieved. The gripping force generated by this mechanism was calculated, and it was found that the gripping force varied depending on the size of the object. Finally, the actual forces exerted by the fingers during landing on objects like safety cones, boards, or pipes were measured and compared with theoretical values
This paper proposes a mechanism for a multirotor unmanned aerial vehicle to perch at the tip of a cylindrical object. The proposed mechanism does not require an additional actuator such as a motor by converting its own weight into a gripping force at the time of perching. It also shows that a gripping force larger than its own weight can be generated based on a boost mechanism by appropriately selecting the design parameters. In addition, the proposed mechanism has a structure that can be not only used for perching at the tip of a cylindrical object, but also as a landing gear when landing on flat ground. Furthermore, we attached a depth camera to the proposed mechanism and obtain color and depth images of the target object to be grasped while flying so that automatic positioning can be executed based on the acquired images. Through indoor and outdoor experiments, it was confirmed that the expected perching and landing could be performed.