Vincent Vanel

Vincent Vanel

Auto-generated profile, based on publicly available information

Vincent Vanel

CEA, DES, ISEC, DMRC, University Montpellier

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 April 2020 in Solvent Extraction and Ion Exchange
Verified
Journal Article
Closed access
MMManuel Miguirditchian
Manuel Miguirditchian
VVVincent Vanel
Vincent Vanel
CMCécile Marie
Cécile Marie
VPVincent Pacary
Vincent Pacary
MCMarie-Christine Charbonnel
Marie-Christine Charbonnel
CPChristophe Poinssot
Christophe Poinssot
In the framework of the R&D program conducted in France on partitioning and transmutation of minor actinides, a solvent extraction process was developed for separating americium from a PUREX raffinate arising from the dissolution of spent nuclear fuels in nitric acid. The so-called EXAm process uses a mixture of a malonamide (DMDOHEMA, N,N’-dimethyl-N,N’-dioctyl-hexyloxyethyl-malonamide) and HDEHP (di-2-ethylhexylphosphoric acid) in organic phase in combination with a water-soluble complexing agent TEDGA (N,N,N’,N’-tetraethyldiglycolamide) in aqueous phase to enhance Am/Cm separation. Am/Ln separation is then obtained by selective Am stripping with polyaminocarboxylic acids (HEDTA or DTPA) buffered by citric or malonic acid at low acidity. Started in 2008, an important R&D program was conducted at CEA to optimize and model the process. The feasibility of the direct recovery of Am from a genuine PUREX raffinate by solvent extraction was demonstrated in 2010 and reported, for the first time in the literature. R&D was then conducted to adapt the process for a future scale-up and for application from concentrated PUREX raffinates. The results of the final EXAm process performed on a highly active PUREX concentrate are presented after a summary of 10 years of R&D on this process development.

26 July 2019 in Solvent Extraction and Ion Exchange
Verified
Journal Article
Closed access
CMCécile Marie
Cécile Marie
PKPeter Kaufholz
Peter Kaufholz
VVVincent Vanel
Vincent Vanel
MDMarie-Thérèse Duchesne
Marie-Thérèse Duchesne
EREmilie Russello
Emilie Russello
MMManuel Miguirditchian
Manuel Miguirditchian
Recycling americium from spent nuclear fuel is considered as an important option for a future sustainable nuclear fuel cycle. The PUREX solvent extraction process allows to separate uranium and plutonium from a solution of spent fuel dissolved in nitric acid. In a second step, it would be desirable to separate americium from fission products, and especially lanthanides, but also from curium in order to further transmute americium in future fast neutron reactors. For this purpose, we report the investigation of a new solvent extraction process based on the use of TODGA as an extractant in the organic phase and H4TPAEN as a selective Am(III) stripping agent in the aqueous phase. With this promising system it is possible to co-extract Am, Cm and lanthanides at high acidity and then selectively strip americium from the loaded organic phase at pH around 1 with H4TPAEN. Batch extraction data were acquired to evaluate best conditions to develop a liquid-liquid extraction flow sheet. The influence of several parameters like concentration of ligand, cations and temperature on Am(III)/Cm(III) and Am/lanthanides separation was evaluated. Especially, the ability of H4TPAEN complexing agent to strip macro-concentrations of Am was demonstrated.

1 January 2016 in Procedia Chemistry
Verified
Journal Article
Open access
VVV. Vanel
V. Vanel
MBM.-J. Bollesteros
M.-J. Bollesteros
CMC. Marie
C. Marie
MMM. Montuir
M. Montuir
VPV. Pacary
V. Pacary
VBV. Boyer-Deslys
V. Boyer-Deslys

1 January 2016 in Procedia Chemistry
Verified
Journal Article
Open access
VVV. Vanel
V. Vanel
CMC. Marie
C. Marie
PKP. Kaufholz
P. Kaufholz
MMM. Montuir
M. Montuir
NBN. Boubals
N. Boubals
CSC. Sorel
C. Sorel
Recycling americium from spent fuels is an important consideration for the future nuclear fuel cycle, as americium is the main contributor to the long-term radiotoxicity and heat power of the final waste, after separation of uranium and plutonium using the PUREX process. The separation of americium alone from a PUREX raffinate can be achieved by co-extracting lanthanide (Ln(III)) and actinide (An(III)) cations into an organic phase containing the diglycolamide extractant TODGA, and then stripping Am(III) with selectivity towards Cm(III) and lanthanides. The water soluble ligand H4TPAEN was tested to selectively strip Am from a loaded organic phase. Based on experimental data obtained by Jülich, NNL and CEA laboratories since 2013, a phenomenological model has been developed to simulate the behavior of americium, curium and lanthanides during their extraction by TODGA and their complexation by H4TPAEN (complex stoichiometry, extraction and complexation constants, kinetics). The model was gradually implemented in the PAREX code and helped to narrow down the best operating conditions. Thus, the following modifications of initial operating conditions were proposed:• An increase in the concentration of TPAEN as much as the solubility limit allows. • An improvement of the lanthanide scrubbing from the americium flow by adding nitrates to the aqueous phase. A qualification of the model was begun by comparing on the one hand constants determined with the model to those measured experimentally, and on the other hand, simulation results and experimental data on new independent batch experiments. A first sensitivity analysis identified which parameter has the most dominant effect on the process. A flowsheet was proposed for a spiked test in centrifugal contactors performed with a simulated PUREX raffinate with trace amounts of Am and Cm. If the feasibility of the process is confirmed, the results of this test will be used to consolidate the model and to design a flowsheet for a test on a genuine PUREX raffinate. This work is the result of collaborations in the framework of the SACSESS European Project

1 January 2012 in Procedia Chemistry
Verified
Journal Article
Open access
VVVincent Vanel
Vincent Vanel
LBLaurence Berthon
Laurence Berthon
JMJulie Muller Manuel Miguirditchian
Julie Muller Manuel Miguirditchian
FBFabien Burdet
Fabien Burdet
The EXAm process aims at recovering americium alone contained in the PUREX raffinate. The americium stripping model has been revised to take into account a change of stripping aqueous phase and up-to-date experimental results conducted within DRCP to improve knowledge about complexes.This work represents a first approximation at modelling americium stripping. The modelling work has led to synthesize the knowledge on chemical phenomenology and adopt assumptions that best reflect experimental results. The modelling has been implemented in PAREX code in order to simulate this step to prepare and understand tests to be carried out in mixer settlers

16 June 2016 in Solvent Extraction and Ion Exchange
Verified
Journal Article
Closed access
CMCécile Marie
Cécile Marie
VVVincent Vanel
Vincent Vanel
SWSou Watanabe
Sou Watanabe
MDMarie-Thérèse Duchesne
Marie-Thérèse Duchesne
NZNicole Zorz
Nicole Zorz
LBLaurence Berthon
Laurence Berthon
The EXAm (extraction of americium) process was developed for americium recycling in future nuclear fuel cycles. In this solvent extraction system, a combination of two extractants, N,N′-dimethyl-N,N′-dioctyl-hexylethoxy malonamide (DMDOHEMA) and di-2-ethylhexyl phosphoric acid (HDEHP), in TPH (hydrogenated tetrapropylene) is used to extract americium in the first step of the process at high acidity (HNO3 5–6 M). Americium is co-extracted with light lanthanides and other fission products like molybdenum, iron, ruthenium, etc.. Molybdenum is selectively scrubbed during the second step at low acidity using citric or glycolic acid as a buffer and complexing agent. The speciation of Mo(VI) in aqueous solutions is highly dependent on acidity and Mo concentration. In this article, a simple thermodynamical model is proposed for Mo(VI) scrubbing based on batch extraction experiments (with pH and cation concentration variations) and stoichiometries of complexes formed in the organic phase according to electrospray ionization mass spectrometry (ESI-MS) experiments and published data on Mo(VI) speciation. At high acidity ([HNO3] > 1 M), the MoO22+ species is strongly extracted by the solvent DMDOHEMA–HDEHP according to a solvate mechanism. At lower acidity ([HNO3] < 1 M), cation exchange mechanisms become predominant and DMDOHEMA does not participate to the extraction Mo(VI) anymore. During Mo scrubbing at pH higher than 1, the extraction of Mo as neutral species (like MoO3) and anionic species (like MoO42–) has to be taken into account in the model to predict the “bell-shape” of Mo distribution ratio evolution as a function of pH. This model was then implemented in the PAREX simulation code developed by the CEA to build the flowsheet for the “Mo scrubbing” section of EXAm process and predict Mo concentrations profiles in batteries of mixer-settlers during pilot-scale tests.