16 March 2017 in Optics Express
Frequency-comb-based Brillouin optical time-domain analysis (BOTDA) sensors were developed to achieve acquisition-time reduction and high-spatial-resolution/long-distance sensing simultaneously. We found that, for the standard frequency-comb-based BOTDA, the use of a double-sideband (DSB) pulse generates a series of pulse pairs that simultaneously propagate along the sensing fiber, leading to a nonlinear interaction between the two sidebands of each frequency comb pulse, and a significant splitting of the Brillouin gain spectrum (BGS). This problem prevents its application in high-spatial-resolution sensing due to the higher pulse power requirement. Thus, one of the sidebands of DSB pulse was proposed for greatly suppressing the BGS distortion. In combination with the phonon pre-excitation technique based on phase-shifted pulse, a sensor with a spatial-resolution approximately 60 cm along a fiber approximately 592 m in length was demonstrated. Furthermore, we explored the detailed performance of long-distance sensing by frequency- comb-based BOTDA. The use of a frequency comb for the probe wave can suppress the pulse distortion and non-local effect, which is helpful for extending the sensing distance. A spatial resolution of approximately 6 m along a sensing fiber approximately 74.2 km in length was successfully demonstrated.
1 September 2021 in Optics Communications
9 May 2022 in IEEE Journal of Quantum Electronics
We proposed a new reservoir computation (RC) structure using polarization dynamics of vertical cavity surface emitting lasers (VCSELs) with optoelectronic feedback. Santa-Fe time-series prediction and nonlinear channel equalization were used to evaluate its parallel processing capability. We numerically discussed the effects of feedback strength, injection strength, frequency detuning, injection current and scaling factors on the RC performance of the system. The results show that, the operation range of negative feedback is larger than that of positive feedback; under appropriate feedback and lager injection strengths, good RC performance can be achieved for a wider injection current; with continuous variation of feedback strength from negative to positive values, the optimized location for frequency detuning moves from positive to negative values. We also evaluated the processing rate of proposed RC structure. The related study is helpful for the design and optimization of VCSEL-based RC under optoelectronic feedback.
15 June 2016 in Optics Express
A novel approach for long-distance sensing through Brillouin optical time-domain analysis (BOTDA) assisted by second-order distributed Brillouin amplification (DBA) was proposed and experimentally demonstrated. To the best of our knowledge, this is the first BOTDA study that used second-order DBA. Compared with BOTDA assisted by first-order DBA, the proposed approach enhanced the signal-to-noise ratio of the Brillouin trace by ~3 dB for a range featuring minimum sensing intensity. Long-distance sensing with ~5 m spatial resolution and ± 1.6°C measurement uncertainty over ~99 km fiber was successfully realized by employing high-efficiency pumping using ~6 dBm second-order and ~1.5 dBm first-order pumps.
7 November 2014 in Optics Express
All-optical temporal integrator using phase-shifted distributed-feedback semiconductor optical amplifier (DFB-SOA) is investigated. The influences of system parameters on its energy transmittance and integration error are explored in detail. The numerical analysis shows that, enhanced energy transmittance and integration time window can be simultaneously achieved by increased injected current in the vicinity of lasing threshold. We find that the range of input pulse-width with lower integration error is highly sensitive to the injected optical power, due to gain saturation and induced detuning deviation mechanism. The initial frequency detuning should also be carefully chosen to suppress the integration deviation with ideal waveform output.
29 August 2022 in IEEE Photonics Journal
We propose and experimentally demonstrate an integrated passive optical network monitoring system for fault detection and localization. Fault detection technology is based on the recognition of reflection spectrum generated by each single fiber Bragg grating, which can support large-capacity user fiber fault monitoring. Fault localization method uses two different total received powers measured by an optical power meter to solve the established equation, and it shows a good accuracy compared with the OTDR measurement results. Fault detection and localization are carried out separately but share the same transmitter module. The introduction of the additional module ensures that the troubleshooting does not affect other normal user data communication. We also investigate the dynamic range requirements of the fault detection technology and the measurement error of the fault localization method. The calculation results show the required dynamic range for the recognition device can be maintained within a small range and the use of high-accuracy optical power meter can reduce the measurement error. The proposed monitoring system can simultaneously provide a large-capacity fault detection technology and high-accuracy fault localization method in a cost-sensitive passive optical network market.