Min Shi

Min Shi

Auto-generated profile, based on publicly available information

Min Shi

Wuhan University of Technology

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 March 2018 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
MSMin Shi
Min Shi
DZDaohai Zhang
Daohai Zhang
JZJianhua Zhu
Jianhua Zhu
YSYinping Shi
Yinping Shi
JSJing Sun
Jing Sun
YJYubi Ji
Yubi Ji
Dynamically vulcanized thermoplastic olefin based on polypropylene (PP)/ethylene–propylene–diene (EPDM) with different dicumyl peroxide (DCP) content was prepared by twin-screw extruder. The effect of DCP content on gel content, crystallinity, and morphological, thermal, and mechanical properties of dynamically vulcanized EPDM/PP blends with different DCP content was investigated. The scanning electron microscopy was performed to evaluate the structure, as well as to characterize the morphology formed during dynamic vulcanization. The regular cross-linked EPDM particle uniformly distributed in PP matrix when the DCP content was from 0.3% to 0.9%. The crystallization behavior analysis indicated that the cross-linked EPDM promoted the nucleation process of PP, but with increase in DCP content, the percentage of crystallinity of the dynamically vulcanized EPDM/PP blends decreased due to the PP degradation. The tensile strength and elongation at break first increase and then decrease with increase in DCP content. When the DCP content was 0.9%, the tensile strength and elongation at break of dynamically vulcanized EPDM/PP blends were the largest. The gel content of dynamically vulcanized EPDM/PP blends first increased and then decreased with increasing DCP content. When the DCP content was 1.2%, the gel content of dynamically vulcanized EPDM/PP blends was maximum. The proper content range of DCP was from 0.6% to 1.2%.

10 October 2021 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
JSJing Sun
Jing Sun
AHAnrong Huang
Anrong Huang
SLShanshan Luo
Shanshan Luo
MSMin Shi
Min Shi
JSJiling Song
Jiling Song
HLHeng Luo
Heng Luo
Biodegradable poly(butylene adipate-co-terephthalate)/poly(lactic acid) (PBAT/PLA) composites were prepared by melt blending, and chain extender was used to improve the compatibility of PBAT/PLA blends through the chemical reaction. The influence of PLA and chain extender contents on mechanical properties, morphology, and rheological properties of PBAT/PLA composites was systematically investigated. The results revealed that the Young’s modulus and stress values gradually increased under the same strain, whereas the elongation at break decreased with the increase of chain extender content for PBAT/PLA (80/20) composites. Noteworthy, the presence of chain extender improves the interfacial compatibility between PLA and PBAT phases. At the chain extender content of 0.4, 0.6, and 0.8 wt.%, the extensional viscosity of the composites exhibited an increasing trend, whereas an obvious strain-hardening phenomenon emerged in the uniaxial extensional curves.

2 February 2018 in Journal of the Chinese Chemical Society
Verified
Journal Article
Closed access
PDF file
PZPingbo Zhang
Pingbo Zhang
MSMin Shi
Min Shi
MFMingming Fan
Mingming Fan
PJPingping Jiang
Pingping Jiang
YDYuming Dong
Yuming Dong

15 July 2020 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
JSJing Sun
Jing Sun
AHAnrong Huang
Anrong Huang
SLShanshan Luo
Shanshan Luo
MSMin Shi
Min Shi
HLHeng Luo
Heng Luo
YSYuanming Sui
Yuanming Sui
In situ microfibrillar ethylene–octene copolymer (POE)/poly(lactic acid) (PLA) composites (MFCs) with different phase morphologies were prepared by controlling the stretching speed and maintaining the weight ratio of POE/PLA of 80/20. Four different stretching speeds were employed to study the effect of PLA microfibrillar morphology on tensile, crystalline, and rheological properties of MFCs. Scanning electron microscopic images revealed that the morphology of PLA phase was strongly influenced by stretching speed. MFCs with highest aspect ratio and smaller diameter of PLA microfibrils were obtained with a stretching speed of 60 rpm. The PLA microfibrils with high aspect ratio had the best reinforcement effect on MFCs. The dynamic rheological properties indicated that the MFCs achieved higher storage modulus and loss modulus at the stretching speed of 60 rpm.

9 July 2018 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
JSJing Sun
Jing Sun
LWLiangqiang Wei
Liangqiang Wei
SLShanshan Luo
Shanshan Luo
AHAnrong Huang
Anrong Huang
MSMin Shi
Min Shi
Poly(propylene carbonate) (PPC) blended with poly(butylene succinate) (PBS) with chain extender (CE) was prepared by melt mixing. Mechanical properties of PPC/PBS composites showed that the addition of CE can increase its tensile strength and unnotched impact strength, and the PPC/PBS composites had higher tensile strength when CE (0.4 wt%) was added into PPC/PBS composites. Thermogravimetric measurements revealed that adding CE to PPC/PBS (70/30 wt%) can improve the thermal decomposition temperatures ( T −5% and T −10%). Dynamic mechanical analysis revealed that the incorporation of CE increased the storage modulus of the PPC/PBS (70/30 wt%) composites.

1 September 2014 in Advanced Materials Research
Verified
Journal Article
Closed access
PDF file
KHKun Huang
Kun Huang
WPWei Cai Peng
Wei Cai Peng
ZHZhi Xiong Huang
Zhi Xiong Huang
MSMin Xian Shi
Min Xian Shi
GWGuang Bing Wan
Guang Bing Wan
Instantaneous signal and alternating signals are as driven signals, using PID control, change control coefficient P's size, The stopping time of impact force under instantaneous signal with the piezoelectric ceramic content increases, the stopping time is reduced; after applying active control, the stopping is shorter than that is not applied. After applying the alternating signal to force the cantilever beam, the driving effect of the ceramic sheet is located in a cantilever position A, B, C, the effect of C under controlling is at best. The effect of two driven ceramic sheets is better than that of three driven ceramic sheets, the best control position is B+C.