28 November 2021 in Fine Chemical Technologies
Objectives. Recently, there has been a tendency to increase the volume of high-viscosity heavy oils in the total volume of oil produced. The processing of these oils requires new technological approaches. This task is closely related to the need to increase the depth of oil refining. Among the approaches proposed to solve these problems, mechanochemical activation, which is based on the cavitation effect produced by ultrasonic or hydrodynamic methods, has been suggested. This study evaluated the effects of cavitation in increasing the depth of oil refining.Methods. Straight-run and “secondary” oil products were used as raw materials: vacuum gas oil, catalytic cracking gas oil, and fuel oil. Activation was carried out in a high-pressure disintegrator. The principle of operation was to compress the oil product and then pass it through a diffuser. When the oil was passed through the diffuser, there was a sharp pressure release to atmospheric pressure, which caused cavitation in the hydrodynamic flow. The pressure gradient on the diffuser and the number of processing cycles ranged from 20 to 50 MPa and 1 to 10, respectively. The density, refractive index, and the fractional composition of petroleum products were determined using standard and generally accepted methods.Results. This paper reports the influence of mechanochemical activation of petroleum products on their physical and chemical characteristics. An increase in the pressure gradient and the number of processing cycles leads to a decrease in the boiling point of the petroleum products and their density and an increase in the yield of fractions that boil off below 400 °C. The yield of the fractions with boiling points of 400–480 °C and the remainder were reduced. The density and refractive index of fractions with boiling points up to 480 °C decreased, and the density of the residue increased. The effects of cavitation (an increase in the yield of fractions with boiling points up to 400 °C and a decrease in the density of the petroleum products) increased with increasing pressure gradient and the number of processing cycles.Conclusions. The changes in the density, boiling point, and the yield of fractions increased with increasing the pressure from 20 to 50 MPa and the number of hydrodynamic cavitation cycles from 1 to 5. Increasing the number of processing cycles to more than five had little additional effect. The effects of cavitation increased with increasing initial density of the oil product. The average molecular weight of these fractions was estimated from the densities and boiling points of individual fractions of the petroleum products. The calculation confirmed the assumption regarding the course of cracking reactions of petroleum products under the influence of cavitation and indicates the course of the compaction processes.
9 April 2022 in Fine Chemical Technologies
Objectives. A characteristic feature of oil production is an increase in the volume of highviscosity bituminous oil. In Russia, technologies based on the use of water vapor are used for their extraction. The use of such technologies leads to a large amount of water in the product stream from the production well. Preparation of oil for processing involves its stabilization, desalination, and dewatering. Since the densities of the extracted oil and the water contained in it are comparable, traditional preparation schemes for processing of high-viscosity bituminous oil are ineffective. One of the possible solutions to the problem involving such oil in the fuel, energy, and petrochemical balance is to use a coking process at the first stage of its processing. This aim can be achieved by studying the influence of the process conditions of coking high-viscosity water-containing oil on the yield and characteristics of the resulting products.Methods. Coking of oil with a density of 1.0200 g/cm3 at 50 °C and with 18 wt % water content was carried out in a laboratory installation in a “cube.” A hollow cylindrical apparatus was used as a reactor and was placed in a furnace. The temperature and pressure in the reactor were maintained at 500–700 °C and 0.10–0.35 MPa, respectively.Results. An increase in the coking process temperature results in an increase in the amount of gaseous products, a decrease in the amount of the coke generated, and a higher dependence of the amount of liquid products on temperature with a maximum yield at 550–600 °C. The process temperature also affects the composition of liquid products. At a lower temperature, the amount of gasoline and kerosene fractions in liquid products is higher. With an increase in pressure, a higher amount of gaseous products, coke, and low-molecular-weight hydrocarbon fractions in liquid products could also be obtained. The characteristics of the coke produced in the coking process are similar to those of commercially produced grades. It is noted that when coking water-containing oil, up to 98% of the emulsion water goes with liquid products, and the remaining amount of water remains in the formed coke.Conclusions. Results showed the possible application of the coking process at the initial stage of processing high-viscosity bituminous oil. In this case, the dewatering stage is significantly simplified since the technological scheme of delayed coking allows the separation of the gasoline fraction from water.
7 November 2025 in Fine Chemical Technologies
Objectives . To investigate the influence of hydrodynamic cavitation on the group hydrocarbon composition of straight-run fuel oil and the structural characteristics of its asphaltenes. Methods . The cavitation treatment of fuel oil was carried out in hydrodynamic mode using a Donor-2 device. The pressure drop in the working part was 50 MPa, while the number of treatment cycles varied from 1 to 10. In some cases, to intensify the process, the fuel oil was compounded with low-boiling hydrocarbons (propane-butane fraction, decalin). The determination of the group hydrocarbon composition of the sample was based on the different solubility of hydrocarbons in polar and nonpolar solvents; asphaltenes were studied by diffractometry and Raman spectroscopy. Results . It is shown that the group hydrocarbon composition of the sample changes as a result of the cavitation effect: the content of resins and asphaltenes decreases, the amount of the oil fraction increases, and its group hydrocarbon composition is altered. It was found that cavitation exposure also changes the structural characteristics of asphaltenes: they decrease the La and Lc crystallite parameters that characterize their dimensions in plane and height, as well as increase the distance between alkyl substituents and the degree of plasticity of asphaltenes. The processing of Raman spectra by various methods demonstrated consistent results: in all cases, an increase in the intensity of exposure led to an increase in the structural disorder of asphaltenes. In the case of preliminary compounding of the sample with low-boiling hydrocarbons, the effect of cavitation was enhanced. Conclusions . The results obtained may indicate the localization of cavitation bubbles at the boundaries of complex structural units of the dispersed petroleum system formed by asphalt-resinous substances and a dispersion medium. For this reason, it is resins and asphaltenes that are most exposed to the thermal effects that occur when cavitation bubbles collapse. The destruction of resins and asphaltenes leads to a decrease in the size of complex structural units and consequent decrease in the viscosity of the petroleum dispersed system, while the oil fraction is enriched with saturated hydrocarbons.
24 January 2023 in Fine Chemical Technologies
Objectives. The reduction of the anthropogenic burden on the environment is generally associated with the transition to alternative energy sources. However, some of these have only regional significance, while the effectiveness of others remains doubtful. On this point, innovative processes aimed at increasing the depth of oil refining may be equally important for reducing the carbon footprint. Wave-based technologies such as cavitation may also be included in these processes. Among the various methods for inducing such cavitation phenomena in oil refining, hydrodynamic approaches are especially promising. It has been shown that the treatment effectiveness increases with greater pressure or when augmenting the number of cavitation processing cycles. The aim of this work is to identify the factor (i.e., pressure gradient or number of treatment cycles) having the greatest influence on the change of the characteristics of the oil product.Methods. Cavitation phenomena were created by pumping dark oil products through a diffuser. The pressure gradient ranged from 20 to 50 MPa, while the number of cavitation processing cycles varied from 1 to 10. The influence of cavitation conditions on the change of fractional composition of petroleum products was analyzed. Target fractions are those having a boiling point up to 400°C.Results. It is shown that increased pressure generated in the diffuser leads to a linear increase in the yield of desired cuts. The dependence of the yield of these fractions on the number of processing cycles is described by the growth model with saturation. A proposed equation describes the influence of pressure and number of cycles on the yield of the fractions from initial boiling point temperature (TIBP) to 400°C following cavitation processing of dark oil products. Some of the coefficients of this equation have been associated with the physicochemical characteristics of the feedstock.Conclusions. An equation for predicting the maximum possible yield of the TJBP-400°C fraction as a result of cavitation processing under different conditions of the process is proposed according to the physicochemical characteristics of the feedstock. The prediction error did not exceed 12%. The equation analysis and comparison of energy consumption between different process regimes shows that a higher yield of the target product is achieved by increasing pressure gradient rather than the number of processing cycles.
6 May 2026 in Fine Chemical Technologies
Objectives. While the phenomenon of cavitation is of interest for treatment of hydrocarbon mixtures, in particular crude oil and petroleum products, the literature lacks a systematic approach to conducting such research. This gap stimulates the need for a more in-depth study of the influence of this physical effect on the characteristics and detailed hydrocarbon composition of petroleum feedstock. Thus, the present work set out to explore the influence of the conditions leading to cavitation on the physicochemical properties and hydrocarbon composition of crude oil and petroleum products. Methods. The objects of the study were two crude oil samples and four straight-run fractions—gasoline, kerosene, diesel, and fuel oil—having different characteristics and hydrocarbon compositions. Cavitation treatment was carried out in a hydrodynamic mode using a Donor-2 apparatus within a range of pressure changes from 20 to 50 MPa. The number of treatment cycles was from 1 to 20. The density was determined by pycnometry using the refractive index, an Abbe refractometer, and the fractional composition or fraction yield, as well as by distillation at atmospheric or reduced pressure for light or dark petroleum products, respectively. The hydrocarbon composition of the gasoline fraction was determined by chromatography and mass spectrometry. Results. Changes in the densities and fractional compositions of the objects of study following their treatment under various conditions were recorded. Particular attention was paid to the hydrocarbon composition of the gasoline fraction: an increase in the content of normal alkanes was shown to be due to an increase in the number of structures with shorter carbon chains in comparison with the components of raw materials not subjected to cavitation. Conclusions. The results of the study of the effect of cavitation treatment of crude oil and its individual fractions on their physicochemical characteristics showed that the nature of the changes depends on the treatment conditions and the initial characteristics of the sample. It is suggested that cavitation treatment causes cracking and compaction processes. The possibility of cracking reactions was confirmed by chromatographic determination of the group hydrocarbon composition of the samples.