Ratcheting failure of materials and structures subjected to low cycle fatigue in the presence of significant mean stress is of great interest to researchers. In this experimental and numerical study, the response of 316L stainless steel samples was observed in symmetric strain control uniaxial test followed by post-stabilized monotonic test, uniaxial and biaxial ratcheting tests, in order to determine the Chaboche model parameters and to evaluate ratcheting prediction using finite element analysis. The critical elastic limit was initially obtained from incremental uniaxial cyclic tests. The Chaboche parameters were subsequently extracted from experimental hysteresis and post-stabilized monotonic stress plastic-strain curves using two optimization technics, namely, the Particle Swarm Optimization (PSO) and Genetic Algorithm (GA). The two optimization methods were compared for efficiency, in terms of time and accuracy. The PSO method presented higher efficient results and was subsequently used to derive the parameters from hysteresis and post-stabilized monotonic curves. Different values (by definition) of elastic limit were also used. The Finite Element commercial software ANSYS was utilized with the Chaboche model to predict the uniaxial and biaxial ratcheting behavior of 316L stainless steel pipe. The comparison between experimental and the numerical simulation demonstrates that adopting post-stabilized monotonic curve rather than hysteresis curve and with accurate elastic limit obtained from incremental loading test improves ratcheting prediction significantly.
In the field of orthopedics, magnesium (Mg) and magnesium-based composites as biodegradable materials have attracted fundamental research. However, the medical applications of magnesium implants have been restricted owing to their poor corrosion resistance, especially in the physiological environment. To improve the corrosion resistance of Mg/HA/TiO2 nanocomposites, monolayer MgO and double-layer Si/MgO coatings were fabricated layer-by-layer on the surface of a nanocomposite using a powder metallurgy route. Then, coating thickness, surface morphology, and chemical composition were determined, and the corrosion behavior of the uncoated and coated samples was evaluated. Field-emission scanning electron microscopy (FE-SEM) micrographs show that an inner MgO layer with a porous microstructure and thickness of around 34 μm is generated on the Mg/HA/TiO2 nanocomposite substrate, and that the outer Si layer thickness is obtained at around 23 μm for the double-layered coated sample. Electrochemical corrosion tests and immersion corrosion tests were carried out on the uncoated and coated samples and the Si/MgO-coated nanocomposite showed significantly improved corrosion resistance compared with uncoated Mg/HA/TiO2 in simulated body fluid (SBF). Corrosion products comprising Mg(OH)2, HA, Ca3(PO4)2, and amorphous CaP components were precipitated on the immersed samples. Improved cytocompatibility was observed with coating as the cell viability ranged from 73% in uncoated to 88% for Si/MgO-coated Mg/HA/TiO2 nanocomposite after nine days of incubation.
Hybrid manufacturing in this research is a process that combines additive and subtractive manufacturing in the same equipment. The integration of various manufacturing processes into a single process has been the subject of this study. The goal is to reduce the amount of space, time, cost and labour required for production. While much hybrid manufacturing research has concentrated on expensive and high-level decision-making activities like service composition and scheduling, the link between field-level manufacturing data and the cloud manufacturing platform has yet to be developed. The development of cloud manufacturing systems is hampered by the inefficiency of data gathering, communication, storage, query, and analysis of field-level manufacturing equipment. In order to solve this difficulty, this research will analyze the use of developing Industrial Internet of Things (IIoT) technologies in a cloud manufacturing system. Based on a general system architecture of IIoT-supported cloud manufacturing system offer a service-oriented plug-and-play (PnP) IIoT gateway solution. Manufacturing equipment service-oriented data schemas are being created to capture just-enough data about field-level manufacturing equipment and allow for efficient data storage and query in a cloud time-series database (TSDB). Through the practical deployment of IIoT gateways on a 3D printer and laser marking tool, the feasibility and benefits of the suggested solution as a framework result with overall production nearly 30% reduction. According to findings by using PnP IIoT technologies to connect field-level manufacturing equipment to a cloud platform, purposefully built service-oriented data schemas that capture the critical information for high-level hybrid manufacturing decision-making are a solid solution. Finally, this can be increased productivity of making components by using low cost hybrid 3D printing process which can support the digital manufacturing integration approach in the future. Keywords 3D Printing, Emerging Technologies, Digital Manufacturing, Proses integration