1 May 2012 in Nuclear Fusion
The non-linear reduced four-field RMHD model in cylindrical geometry was extended to include plasma rotation, neoclassical poloidal viscosity and two fluid diamagnetic effects. Interaction of the static resonant magnetic perturbations (RMPs) with the rotating plasmas in tokamaks was studied. The self-consistent evolution of equilibrium electric field due to RMP penetration is taken into account in the model. It is demonstrated that in the pedestal region with steep pressure gradients, mean flows perpendicular to the magnetic field, which includes and electron diamagnetic components plays an essential role in RMP screening by plasma. Generally, the screening effect increases for lower resistivity, stronger rotation and smaller RMP amplitude. Strong screening of central islands was observed limiting RMP penetration to the narrow region near the separatrix. However, at certain plasma parameters and due to the non-linear evolution of the radial electric field produced by RMPs, the rotation can be compensated by electron diamagnetic rotation locally. In this case, RMPs can penetrate and form magnetic islands. Typical plasma parameters and RMPs spectra on DIII-D, JET and ITER were used in modelling examples presented in the paper.
18 October 2016 in Plasma Physics and Controlled Fusion
3D non-linear MHD simulations of a D 2 massive gas injection (MGI) triggered disruption in JET with the JOREK code provide results which are qualitatively consistent with experimental observations and shed light on the physics at play. In particular, it is observed that the gas destabilizes a large m / n = 2/1 tearing mode, with the island O-point coinciding with the gas deposition region, by enhancing the plasma resistivity via cooling. When the 2/1 island gets so large that its inner side reaches the q = 3/2 surface, a 3/2 tearing mode grows. Simulations suggest that this is due to a steepening of the current profile right inside q = 3/2. Magnetic field stochastization over a large fraction of the minor radius as well as the growth of higher n modes ensue rapidly, leading to the thermal quench (TQ). The role of the 1/1 internal kink mode is discussed. An I p spike at the TQ is obtained in the simulations but with a smaller amplitude than in the experiment. Possible reasons are discussed.
23 October 2020 in Nuclear Fusion
4 September 2025 in Nuclear Fusion
In this chapter, we review the progress in MHD stability, disruptions and control in magnetic fusion research that has occurred over the past (more than) one and a half decades since the publication by Hender et al in 2007 on the same topic as part of the update of ITER Physics Basis. During this period, remarkable progress has been achieved in the understanding of the basic physics and overall control of MHD instabilities through a wide spectrum of dedicated experiments, theory and modeling. The sawtooth activities are probably today one of the best understood of MHD events and very robust control schemes have been developed for reliable operation of tokamaks through core heating. Similarly, significant improvements have been achieved in understanding and control of neoclassical tearing modes, resistive wall modes or locked modes and their control through ECCD or error field control. The field of disruption prediction through application of artificial intelligence, machine learning or deep learning methods, which had already started at the time of the 2007 review, has progressed significantly due to general progress in these fields and application of newer, more sophisticated algorithms. However, although remarkable progress has been achieved in the field of Disruptions, their understanding, prediction, possible avoidance and mitigation still remain probably the most active fields of R&D globally in this field. This is especially because reactor grade machines like ITER and DEMO will be much less tolerant in respect of disruptions and runaway currents, and their occurrences must be either avoided altogether or minimized to an acceptable value without causing any significant hindrance to robust machine operations. This review is intended to present a broad spectrum of the R&D that has occurred in this field in support of ITER, which will also be of immense significance for all future machines, especially reactors like DEMO.
12 November 2021 in Nuclear Fusion
Disruption mitigation remains a critical, unresolved challenge for ITER. To aid in addressing this challenge, a shattered pellet injection (SPI) system was installed on JET and experiments conducted at a range of thermal energy fractions and stored energies in excess of 7 MJ. The primary goals of these experiments were to investigate the efficacy of the SPI on JET and the ability of the plasma to assimilate multiple pellets. Single pellet injections produced a saturation in total radiated energy (W rad) with increasing injected neon content, suggesting total radiation of stored thermal energy. Further increases in injected neon quantities resulted in reduced cooling times and current quench (CQ) durations, indicating higher impurity assimilation. No significant variation in CQ duration or W rad was observed when varying the deuterium content at fixed neon quantities. Higher assimilation, inferred by shorter CQ durations, was measured when a mechanical punch was used to launch the pellets and this was attributed to a lower pellet velocity leading to higher solid content in the pellet plume and larger fragments penetrating deeper into the plasma. Radiation asymmetries averaged over the cooling time were inferred from Emis3D and ranged from 1.6 to 1.9. Asymmetries averaged over the entire disruption sequence were found to increase at higher thermal energy fractions. The radiated energy fractions decreased with increasing thermal energy fractions but this trend was eliminated when toroidal asymmetries were accounted for with Emis3D. Pure deuterium pellets were able to produce cooling times of up to 75 ms with a gradual loss in thermal stored energy of up to 80%. Experiments with multiple pellet injection indicated W rad can be increased through pellet superposition and density can be increased with an additional D2 injection without a reduction in W rad. KPRAD modelling accurately reproduced the cooling times and the CQ duration at high thermal energies. Assimilation estimates from KPRAD indicated CQ rates scale strongly whilst W rad scales weakly and saturates with assimilated neon content. Comparable W rad can be achieved with lower assimilated neon quantities as longer cooling times are attained. Thus reduced neon content can be preferential in a thermal load mitigation scheme as it may reduce radiation asymmetries and prevent flash melting.
1 August 2011 in Journal of Nuclear Materials