15 January 2007 in IEEE Transactions on Circuits and Systems I: Regular Papers
In this paper, we present the analog circuit design and implementation of the components of an adaptive neuromorphic olfaction chip. A chemical sensor array employing carbon black composite sensing materials with integrated signal processing circuitry forms the front end of the chip. The sensor signal processing circuitry includes a dc offset cancellation circuit to ameliorate loss of measurement range associated with chemical sensors. Drawing inspiration from biological olfactory systems, the analog circuits used to process signals from the on-chip odor sensors make use of temporal "spiking" signals to act as carriers of odor information. An on-chip spike time dependent learning circuit is integrated to dynamically adapt weights for odor detection and classification. All the component subsystems implemented on chip have been successfully tested in silicon
26 March 2015 in IEEE Transactions on Biomedical Circuits and Systems
This paper proposes a solution for signal read-out in the MEMS cochlea sensors that have very small sensing capacitance and do not have differential sensing structures. The key challenge in such sensors is the significant signal degradation caused by the parasitic capacitance at the MEMS-CMOS interface. Therefore, a novel capacitive read-out circuit with parasitic-cancellation mechanism is developed; the equivalent input capacitance of the circuit is negative and can be adjusted to cancel the parasitic capacitance. Chip results prove that the use of parasitic-cancellation is able to increase the sensor sensitivity by 35 dB without consuming any extra power. In general, the circuit follows a low-degradation low-amplification approach which is more power-efficient than the traditional high-degradation high-amplification approach; it employs parasitic-cancellation to reduce the signal degradation and therefore a lower gain is required in the amplification stage. Besides, the chopper-stabilization technique is employed to effectively reduce the low-frequency circuit noise and DC offsets. As a result of these design considerations, the prototype chip demonstrates the capability of converting a 7.5 fF capacitance change of a 1-Volt-biased 0.5 pF capacitive sensor pair into a 0.745 V signal-conditioned output at the cost of only 165.2 μW power consumption.
31 July 2014 in IEEE Transactions on Biomedical Circuits and Systems
This paper presents the design and experimental results of a cochlea filter in analog very large scale integration (VLSI) which highly resembles physiologically measured response of the mammalian cochlea. The filter consists of three specialized sub-filter stages which respectively provide passive response in low frequencies, actively tunable response in mid-band frequencies and ultra-steep roll-off at transition frequencies from pass-band to stop-band. The sub-filters are implemented in balanced ladder topology using floating active inductors. Measured results from the fabricated chip show that wide range of mid-band tuning including gain tuning of over 20dB, Q factor tuning from 2 to 19 as well as the bio-realistic center frequency shift are achieved by adjusting only one circuit parameter. Besides, the filter has an ultra-steep roll-off reaching over 300 dB/dec. By changing biasing currents, the filter can be configured to operate with center frequencies from 31 Hz to 8 kHz. The filter is 9 th order, consumes 59.5 ~ 90.0 μW power and occupies 0.9 mm 2 chip area. A parallel bank of the proposed filter can be used as the front-end in hearing prosthesis devices, speech processors as well as other bio-inspired auditory systems owing to its bio-realistic behavior, low power consumption and small size.
1 May 2007 in Microelectronic Engineering
18 April 2007 in IET Nanobiotechnology
Today, the capability of the human olfactory system is still, in many ways, superior to that of the electronic nose. Although electronic noses are often compared with their biological counterpart, they neither mimic its neural architecture nor achieve its discriminating performance. Experimental studies on the mammalian olfactory system suggest that the nasal cavity, comprising of the mucous layer and the olfactory epithelium, performs a degree of chromatographic separation of complex mixtures. Thus receptor cells distributed beneath the mucous layer provide both spatial and temporal chemosensory information. Here we report on the development of an artificial olfactory microsystem that replicates this basic structure. This contains an integrated channel to emulate the nasal cavity and coated with a polymer to mimic the partitioning mucous layer, which is positioned directly over a sensor array. Our system employs an 80 element chemoresistive microsensor array with carbon black/polymer odour-sensitive films combined with a microfluidic package fabricated by micro-stereolithography. Results show that this biomimetic system generates both spatial and temporal odorant signals, with a temporal chemical retention period of up to 170 s. Data analysis has revealed improvements in its ability to discriminate between two simple odours and a set of complex odours. We believe such emulation of the olfactory system can lead to improved odour discrimination within the field of electronic noses.
22 November 2010 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a spike time event coding scheme for transmission of analog signals between configurable analog blocks (CABs) in a programmable analog array. The analog signals from CABs are encoded as spike time instants dependent upon input signal activity and are transmitted asynchronously by employing the address event representation protocol (AER), a widely used communication protocol in neuromorphic systems. Power dissipation is dependent upon input signal activity and no spike events are generated when the input signal is constant. Computation is intrinsic to the spike event coding scheme and is performed without additional hardware. The ability of the communication scheme to perform computation will enhance the computation power of the programmable analog array. The design methodology and analog circuit design of the scheme are presented. Test results from prototype chips implemented using a 3.3-V, 0.35-μm CMOS technology are presented.