6 March 2006 in International Journal of Wildland Fire
A model for fire-induced heating in tree stems is linked to a recently reported model for tissue necrosis. The combined model produces cambial tissue necrosis predictions in a tree stem as a function of heating rate, heating time, tree species, and stem diameter. Model accuracy is evaluated by comparison with experimental measurements in two hardwood and two softwood species: red maple (Acer rubrum), chestnut oak (Quercus prinus), ponderosa pine (Pinus ponderosa), and Douglas-fir (Pseudotsuga menziesii). Results are promising, and indicate that the model predicts stem mortality/survival correctly in ~75–80% of the test cases. A limited sensitivity analysis of model kill depth predictions suggests that the model is more sensitive to required input data for some species than for others, and that the certainty in predicting vascular cambium necrosis decreases as stem diameter decreases.
22 September 2010 in Combustion Science and Technology
Time-resolved radiation and convection heat flux were measured in a series of experimental fires designed to explore heat transfer behavior during the combustion of discontinuous fuel beds. Fuel spacing and height were varied for both buoyancy- and wind-driven combustion. Peak radiation and convection heat fluxes as high as 130 kW/m2 were recorded. Radiation flux had the effect of heating the fuel before flame arrival. Both positive (heating) and negative (cooling) convective heat transfer occurred before flame arrival. Surprisingly, the convection could also be positive or negative after flame arrival, indicating that even when engulfed in flames there were packets of cooler air moving across the sensor. In nearly all cases, short-duration convective heating pulses appear to precede the full onset of combustion, suggesting that convective heating may be critical as a pilot ignition source. Flame spread rate appears to be primarily governed by factors that affect the intensity of the convective transport. Rapid temporal fluctuations were observed in both radiation and convection, and spectral analysis revealed spectral content at frequencies as high as 50–70 Hz under buoyant flow conditions, and 150–200 Hz under the influence of wind.
1 December 2005 in Numerical Heat Transfer, Part A: Applications
Thermally developing electro-osmotically generated flow with in circular microtubes with finite Debye-layer thickness has been analyzed. This study focuses on finite Debye-layer effects, a scenario for which the velocity distribution across the tube cross section varies with the ratio of tube radius and Debye length (termed here the relative microtube radius). Numerical solution of the hydrodynamically developed, thermally developing transport for such a flow is presented in this article. The effect of variations in the relative microtube radius and strength of the Joule and viscous heating on the thermal transport are explored over the possible ranges of the governing parameters.
23 August 2011 in Journal of Heat Transfer
26 March 2018 in Combustion Science and Technology
This paper reports on the modeling of turbulent reacting flow using the advanced Spectral Line Weighted-sum-of-gray-gases (SLW) method for prediction of the gas thermal radiative transfer. Predictions using the traditional weighted-sum-of-gray-gases radiation submodel are compared to the more advanced SLW treatment of radiation transfer. For the problem considered, the results reveal little difference in the predicted H2O and CO2 concentrations between the two radiation submodels. Further, the predicted furnace mass-averaged exit temperature for both radiation submodels is unchanged. However, there is considerable difference in the predicted radiative and thermal structure in the flame zone, albeit at considerably higher computational expense. The use of the more rigorous SLW model significantly affects the accurate resolution of the local radiative heating and local temperature in the flame region. It is concluded that the more advanced SLW model should be used when seeking to resolve accurately the detailed flame structure.
29 January 2010 in Combustion Science and Technology
Experiments were conducted wherein wood shavings and Ponderosa pine needles in quiescent air were subjected to a steady radiation heat flux from a planar ceramic burner. The internal temperature of these particles was measured using fine diameter (0.076 mm diameter) type K thermocouples. A narrow angle radiometer was used to determine the emissive power generated by the burner. A model was developed to predict the steady-state temperature of a cylindrical particle with an imposed radiation heat flux under both quiescent air (buoyancy-induced cooling) and windy (forced convection cooling) conditions. Excellent agreement was observed between the model predictions and the experimental data. Parametric studies using the validated model explore the effect of burner (flame) temperature and distance, fuel size, and wind speed. The data suggest that ignition of the fuel element by radiation heating alone is likely only under circumstances where the fire is very intense (such as crown fires), and even then may still be dependent on pilot ignition sources.