12 June 2023 in Food Chemistry
2 May 2024 in Microchimica Acta
20 July 2026 in ACS Applied Electronic Materials
UKUdhaya Ganesh Pitchai Kaveri
Udhaya Ganesh Pitchai Kaveri
We demonstrate the fabrication of ultrathin, electrically continuous MXene micropattern arrays using a solution-phase, capillarity-driven microchannel templating approach. This strategy overcomes common integration barriers, including weak ink–substrate adhesion, inlet flake bridging, film delamination, and poor geometric confinement during micropattern formation. An open-ended PDMS microchannel template was conformally laminated onto a glass substrate, enabling pump-free wicking of aqueous MXene ink driven by capillary pressure at the liquid–air meniscus. Surface-engineered hydrophilic PDMS enhanced capillary wettability and stabilized meniscus propagation, while amine-functionalized glass substrates promoted strong interfacial adhesion through electrostatic interactions. Together, these modifications improved geometric confinement and film retention during solvent evaporation. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) confirmed successful etching and delamination of F-terminated MXene nanosheets, which are well-suited for confined-flow deposition. Optical microscopy-guided optimization identified 35 μm as the optimal channel width, effectively suppressing inlet blockage while improving flake redistribution and pattern fidelity. Atomic force microscopy (AFM) revealed stepwise thickness growth of approximately 10–15 nm per deposition cycle via sequential fill–dry processing, accompanied by a proportional increase in conductance. This approach enabled the formation of uniform, sub-100 nm-thick, interconnected MXene networks. The resulting MXene micropatterns were integrated into solution-gated field-effect transistor (FET) devices, exhibiting channel-length-linear, ohmic transport characteristics and n-type transfer behavior with a threshold voltage near 0.1 V and an on/off ratio of approximately 5. These FETs enabled the real-time detection of malathion at concentrations ranging from 1 to 20 ppm, producing distinct, stepwise ΔG/G responses.
9 October 2025 in Sensors and Actuators A: Physical
9 October 2026 in ACS Omega
Flexible, freestanding electrodes with high mechanical robustness, electrical conductivity, and electrochemical performance are highly desirable for wearable energy storage devices. Herein, a hierarchical polyaniline/partially oxidized graphene/cellulose nanopaper (PANI/po-Gr/CNP) electrode was developed by integrating redox-active PANI, conductive po-Gr, and mechanically robust cellulose nanofibers (CNFs). PANI-coated CNFs were first prepared via in situ polymerization, followed by incorporation of po-Gr nanosheets. We vacuum-filtered and dried the resulting hybrid suspension to fabricate a freestanding PANI/po-Gr/CNP electrode. Compared with the po-Gr-free PANI/CNP electrode, the optimized PANI/po-Gr/CNP electrode increased electrical conductivity from 0.16 to 1.85 S·cm–1 while maintaining a comparable tensile strength (∼42 MPa). In a three-electrode configuration, the optimized electrode delivered an areal capacitance of 2.74 F·cm–2 at 5 mV·s–1, corresponding to volumetric and gravimetric capacitances of 342.5 F cm–3 and 572.7 F·g–1 (based on the combined mass of PANI and po-Gr), respectively. The assembled symmetric supercapacitor delivered an areal energy density of 58.08 μWh·cm–2 and a volumetric energy density of 7.26 mWh·cm–3, while retaining 81.0% of its initial capacitance after 10,000 charge–discharge cycles. These results show that combining CNFs, PANI, and po-Gr enables a freestanding electrode with a favorable balance of mechanical robustness, electrical conductivity, and electrochemical performance, offering a promising platform for flexible, wearable supercapacitors.