James W. Murray

James W. Murray

Auto-generated profile, based on publicly available information

James W. Murray

University of Nottingham

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2018 in Materials Characterization
Verified
Journal Article
Closed access
MSMarco Simonelli
Marco Simonelli
NANesma T. Aboulkhair
Nesma T. Aboulkhair
PCPhilip Cohen
Philip Cohen
JMJames W. Murray
James W. Murray
ACAdam T. Clare
Adam T. Clare
RHRichard J.M. Hague
Richard J.M. Hague

1 December 2016 in Surface and Coatings Technology
Verified
Journal Article
Open access
SASamer J Algodi
Samer J Algodi
JMJames W Murray
James W Murray
MFMichael Fay
Michael Fay
ACAdam T. Clare
Adam T. Clare
PBPaul D Brown
Paul D Brown
The electrical discharge coating (EDC) process, as used for the development of TiC-Fe cermet coatings on 304 stainless steel, has been investigated as a function of increasing current (2–19 A) and pulse-on time (2–64 μs). Coating morphologies, comprising of a mixture of TiC, γ-Fe, ά-Fe and amorphous carbon, were characterised using the combined techniques of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffractometry (XRD) and cross-sectional transmission electron microscopy (TEM). The developed coatings exhibited variable hardness values, up to an order of magnitude higher than that of the substrate, depending on the content and dispersion of nanostructured TiC particles within the Fe matrix. Coating hardness was found to increase with increasing current, but decrease under conditions of high pulse-on times, reflecting differences in the amount of TiC incorporated into the coatings. Optimised coatings were achieved using conditions of low processing energy which minimised the development of pores and cracks

1 March 2016 in Journal of Materials Processing Technology
Verified
Journal Article
Open access
JMJ.W. Murray
J.W. Murray
JSJ. Sun
J. Sun
DPD.V. Patil
D.V. Patil
TWT.A. Wood
T.A. Wood
ACAdam T. Clare
Adam T. Clare
In EDM, debris plays a key role in the electrical conditions of the discharge gap prior to each spark. Despite this, analysis of debris at all length-scales has not yet been performed, and therefore the nature of debris produced by electrical discharge processes is not fully understood. In this study debris created by the machining of two electrode materials set as negative polarity, silicon and titanium carbide, was centrifuged and imaged using SEM and TEM. From this analysis it was shown that electrode debris is 1nm or lower and up to 10μm in size. Population analysis of the particle size distribution was used to inform an electric field model based on a lattice Boltzmann method framework, simulating the effect of the presence of such debris on the electric field strength. This method is shown to be able to capture the local variation of the electric field and predict qualitatively the correct trend of the electric field strength increasing against the debris concentration. Such data is important for prediction and control of discharge gap size, as well as understanding the impact of a build-up of debris on uncontrolled sparking

1 May 2018 in Wear
Verified
Journal Article
Closed access
SASamer J. Algodi
Samer J. Algodi
JMJames W. Murray
James W. Murray
PBPaul D. Brown
Paul D. Brown
ACAdam T. Clare
Adam T. Clare

1 April 2018 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
JMJames W. Murray
James W. Murray
GRGraham A. Rance
Graham A. Rance
Fang XuFang Xu
Fang Xu
THTanvir Hussain
Tanvir Hussain

1 January 2014 in Procedia CIRP
Verified
Journal Article
Open access
TKTakuma Kawanaka
Takuma Kawanaka
SKShigeki Kato
Shigeki Kato
MKMasanori Kunieda
Masanori Kunieda
JMJames W. Murray
James W. Murray
ACAdam T. Clare
Adam T. Clare
This paper describes development of a method for selective surface texturing using electrolyte jet machining. Electrolyte jet machining is an electrochemical machining method in which dissolution occurs selectively where the electrolyte jet hits the surface of the anode. This process is characterized by the ability to control the surface finish of the removed or added micro patterns by the current density in the electrolyte jet. Higher current density results in a mirror-like surface, while lower current density realizes significantly rough and complicated structures which are difficult to obtain with other machining processes