The discharge of contaminated effluents containing organic dyes is a persistent environmental issue due to their toxicity, stability, and resistance to biodegradation. Among these dyes, malachite green (MG) is particularly concerning because of its widespread industrial use and severe ecological and health impacts. To address this problem, SnO2/Zn2–SnO4 heterostructures were synthesized via sol–gel and evaluated for MG degradation under ultraviolet irradiation. The SnO2/Zn2–SnO4 catalyst has been characterized by X-ray diffraction (XRD), photoluminescence (PL), field-emission scanning electron microscopy coupled with energy-dispersive spectroscopy (FE-SEM-EDS), ultraviolet–visible (UV–vis) spectroscopy, Brunauer–Emmett–Teller method, and electrochemical impedance spectroscopy (EIS). Structural properties revealed that the catalyst presents a polycrystalline structure and crystallite sizes in the range of 11–25 nm. The band gap energy of the Sn:Zn (1:2) catalyst was 2.88 eV, which was lower than that of pure SnO2 (3.33 eV), indicating enhanced light absorption. MG photocatalysis degradation tests were conducted under ultraviolet irradiation. The ZnSn 1:2 sample achieved a degradation efficiency of approximately 96% after 100 min, while the pure SnO2, ZnSn 1:4, and ZnSn 1:6 samples reached only 81%, 88%, and 92%, respectively. This could be due to the presence of h+ and •OH species, which were identified as the most active radicals during the photocatalytic process. Furthermore, the 1:2 ZnSn photocatalyst demonstrated good stability and maintained its photocatalytic performance after five successive degradation cycles. These results indicate that the Zn/Sn 1:2 ratio results in the highest photocatalytic efficiency, confirming the superior effect of Zn2–SnO4 structure in enhancing charge separation and accelerating the degradation of malachite green compared with the other compositions.
The challenge of utilizing green energy sources remains relevant nowadays, especially in developing new catalysts for hydrogen production through complete water decomposition. For this purpose, an electrocatalyst based on an Fe-Ni alloy supported by graphene was synthesized. The catalyst was prepared by using the sol-gel technique. Physicochemical characterization showed that the main crystalline phase was the FeNi alloy with an equimolar ratio. EDS showed that the elements were well distributed on the graphene matrix. Analyzing the structural properties of the catalysts revealed that the GFeNi 1:1.0 catalyst, which has the smallest average crystalline size and lowest lattice strain, exhibited superior catalytic activity due to its high density of exposed active sites. This promotes excellent mass and charge transport during oxygen evolution reaction kinetics. Consequently, the catalysts demonstrated an overpotential of 0.268 V vs RHE at 10 mA/cm2 and maintained good stability in an alkaline 1 M KOH medium. The GFeNi 1:1.0 electrocatalyst showed electrochemical efficiency comparable to that of recently reported catalysts in the literature. These findings advance our understanding of ferromagnetic alloy-based materials for electrolysis applications and other electrochemical devices and highlight the potential of graphene-supported systems synthesized by sol-gel routes as cost-effective alternatives to noble metals.
This study reports the use of graphene-decorated boron nitride (GBN) as an efficient adsorbent for azo dyes, with the aim of treating textile wastewater. GBN was synthesized by a facile route and characterized by XRD, SEM/EDS, TGA-DTA, and BET analyses, revealing a microporous and crystalline structure. Methyl orange (MO) was adopted as a model dye, and batch adsorption experiments were optimized by using response surface methodology (RSM) with pH, adsorbent mass, and initial MO concentration as variables. Results showed that the pH and adsorbent mass were the main factors influencing MO removal. Under optimal conditions (pH 2, 0.062 g of adsorbent, 100 mg/L MO), GBN reached a high adsorption capacity of 322.5 mg/g in 20 min and retained good performance after 10 reuse cycles. The synergistic properties of graphene and boron nitride make GBN a promising material for efficient textile wastewater treatment.