Peter Apata Olubambi

Peter Apata Olubambi

Auto-generated profile, based on publicly available information

Peter Apata Olubambi

University of Johannesburg

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2013 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
KAKeneth Kanayo Alaneme
Keneth Kanayo Alaneme
IAIdris B. Akintunde
Idris B. Akintunde
POPeter Apata Olubambi
Peter Apata Olubambi
TATolulope M. Adewale
Tolulope M. Adewale
The fabrication characteristics and mechanical behaviour of Al-Mg-Si alloy matrix composites reinforced with alumina (Al2O3) and rice husk ash (RHA, an agro-waste) was investigated. This was aimed at assessing the viability of developing high performance Al matrix composites at reduced cost. Al2O3 particulates added with 0, 2, 3, and 4 wt% RHA were utilized to prepare 10 wt% of the reinforcing phase with Al-Mg-Si alloy as matrix using two-step stir casting method. Density measurement, estimated percent porosity, tensile testing, micro-hardness measurement, optical microscopy, and SEM examination were used to characterize the composites produced. The results show that the less dense Al-Mg-Si/RHA/Al2O3 hybrid composites have estimated percent porosity levels as low as the single Al2O3 reinforced grade (< 2.3% porosity). The hardness of the hybrid composites decreases slightly with increase in RHA content with a maximum reduction of less than 11% observed for the Al-4 wt% RHA-6wt% Al2O3 composition (in comparison with the Al-10 wt% Al2O3 single reinforced composition). Tensile strength reductions of 8% and 13%, and specific strengths which were 3.56% and 7.7% lower were respectively observed for the 3 wt% and 4 wt% RHA containing hybrid composites. The specific strength, percent elongation and fracture toughness of the 2 wt% RHA containing hybrid composite was however, higher than that of the single Al2O3 reinforced and other hybrid composite compositions worked on. RHA thus has great promise to serve as a complementing reinforcement for the development of low cost-high performance aluminum hybrid composites

1 September 2008 in Corrosion Science
Verified
Journal Article
Closed access
JPJ.H. Potgieter
J.H. Potgieter
POP.A. Olubambi
P.A. Olubambi
Lesley Alison CornishLesley Alison Cornish
Lesley Alison Cornish
CMC.N. Machio
C.N. Machio
El-Sayed M. SherifEl-Sayed M. Sherif
El-Sayed M. Sherif

1 April 2013 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
KAKenneth Kanayo Alaneme
Kenneth Kanayo Alaneme
POPeter Apata Olubambi
Peter Apata Olubambi
The corrosion and wear behaviour Al–Mg–Si alloy matrix hybrid composites developed with the use of rice husk ash (RHA) and alumina as reinforcements has been investigated. Alumina added with 2, 3, and 4wt.% RHA were utilized to prepare 10wt.% of the reinforcing phase with Al–Mg–Si alloy as matrix using double stir casting process. Open circuit corrosion potential (OCP) and potentiodynamic polarization measurements were used to study the corrosion behaviour while coefficient of friction was used to assess the wear behaviour of the composites. The corrosion and wear mechanisms were established with the aid of scanning electron microscopy. The results show that the corrosion resistance of the single reinforced Al–Mg–Si/10wt.% Al2O3 composite was superior to that of the hybrid composites in 3.5% NaCl solution, and the corrosion rates increased with increase in wt.% RHA. The increase in the population of matrix/reinforcement interface with increase in wt.% RHA in the hybrid composites was identified as the likely reason for the increase in corrosion rates observed with increase in wt.% RHA. The coefficient of friction and consequently, the wear rate of the composites were observed to increase with increase in RHA wt.%. The wear mechanism of the composites was observed to transform from predominantly abrasive wear to a combination of both adhesive and abrasive wear with increase in RHA wt.%

1 January 2014 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
KAKenneth Kanayo Alaneme
Kenneth Kanayo Alaneme
TATolulope Moyosore Adewale
Tolulope Moyosore Adewale
POPeter Apata Olubambi
Peter Apata Olubambi
The corrosion and wear behaviour of Al–Mg–Si alloy matrix hybrid composites developed with the use of rice husk ash (RHA) and silicon carbide (SiC) particulates as reinforcements were investigated. RHA and SiC mixed in weight ratios 0:1, 1:3, 1:1, 3:1, and 1:0 were utilized to prepare 5, 7.5 and 10wt% of the reinforcing phase with Al Mg Si alloy as matrix using double stir casting process. Open circuit corrosion potential (OCP) and potentiodynamic polarization measurements were used to study the corrosion behaviour while coefficient of friction was used to assess the wear behaviour of the composites. The corrosion and wear mechanisms were established with the aid of scanning electron microscopy. The results show that the effect of RHA/SiC weight ratio on the corrosion behaviour of the composites in 3.5% NaCl solution was not consistent for the different weight percent of reinforcement (5, 7.5, and 10wt%) used in developing the Al–Mg–Si based composites. It was evident that for most cases the use of hybrid reinforcement of RHA and SiC resulted in improved corrosion resistance of the composites in 3.5% NaCl solution. Preferential dissolution of the more anodic Al–Mg–Si alloy matrix around the Al–Mg–Si matrix/RHA/SiC particle interfaces was identified as the primary corrosion mechanism. The coefficient of friction and consequently the wear resistance of the hybrid composites were comparable to that of the Al–Mg–Si alloy matrix reinforced with only SiC

1 March 2018 in Ceramics International
Verified
Journal Article
Closed access
MMMosima Edith Maja
Mosima Edith Maja
OFOluwasegun Eso Falodun
Oluwasegun Eso Falodun
BOBabatunde Obadele
Babatunde Obadele
SOSamuel Ranti Oke
Samuel Ranti Oke
POPeter Apata Olubambi
Peter Apata Olubambi

1 November 2015 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MSMxolisi Brendon Shongwe
Mxolisi Brendon Shongwe
SDSaliou Diouf
Saliou Diouf
MDMondiu Olayinka Durowoju
Mondiu Olayinka Durowoju
POPeter Apata Olubambi
Peter Apata Olubambi