A. Ashraf Ghandour

A. Ashraf Ghandour

Auto-generated profile, based on publicly available information

A. Ashraf Ghandour

Department of Mechanical Design and Production Engineering, Faculty of Engineering, Zagazig University, P.O. Box 44519, Zagazig, Egypt.

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 December 2024 in Polymer Composites
Verified
Journal Article
Closed access
AGA. Ashraf Ghandour
A. Ashraf Ghandour
ASA. I. Selmy
A. I. Selmy
MMMona Abo-elwafa Megahed
Mona Abo-elwafa Megahed
AKA. M. Kabeel
A. M. Kabeel
AIAhmed Ibrahim
Ahmed Ibrahim

2 March 2024 in Fibers and Polymers
Verified
Journal Article
Open access
PDF file
AGA. Ashraf Ghandour
A. Ashraf Ghandour
ASA. I. Selmy
A. I. Selmy
MMM. Megahed
M. Megahed
AKA. M. Kabeel
A. M. Kabeel
AIAhmed Ibrahim
Ahmed Ibrahim
Three-dimensional composites (3D) have potential applications in various fields due to their enhanced properties compared to conventional two-dimensional composites (2D). This study investigates the effect of different volumes of z-binder made from copper wire and E-glass fiber on the mechanical properties of 3D woven polymeric composites. The tensile, flexural, and fracture toughness behavior of four types of 3D orthogonal woven composites were studied in addition to a comparative 2D composite. The creation of the 3D orthogonal single-ply fabrics involved weaving z-binders using two different copper wire diameters, single fiber bundles, and double fiber bundles, each combined with four layers of woven E-glass fiber. The consolidation process for both 2D fabric and single-fabric 3D woven composites was executed using the hand lay-up technique. The results showed that most 3D woven composites outperformed 2D composites in terms of fracture toughness (stress intensity factor KIC and energy release rate GIC) and flexural strain. However, a decrease in flexural strength and tensile properties was observed for all 3D composites. The specimen with a small copper diameter had the smallest decrease of 5% in tensile strength. Furthermore, a decrease of 9% and 21% was attained by reinforcing with double and single glass fiber bundle z-binders, respectively, as compared with 2D composites. The highest enhancement of 92.5% in flexural failure strain was attained with double glass fiber bundles of z-binder. The maximum improvement in KIC fracture toughness, reaching 126% and 101.5%, was observed in specimens with a single glass fiber bundle z-binder and those with a large copper wire diameter, respectively.

12 June 2026 in Scientific Reports
Verified
Journal Article
Open access
TSThiru S Samy
Thiru S Samy
ASAbdel-Halim S. Salem Said
Abdel-Halim S. Salem Said
MMM. Megahed
M. Megahed
MAM. A. Agwa
M. A. Agwa
AGA. Ashraf Ghandour
A. Ashraf Ghandour
AJAbdessalem Jarraya
Abdessalem Jarraya
Glass fiber-reinforced polymer composites (GFRP) are widely used in engineering applications thanks to their high performance. This research investigates how various hybrid reinforcement techniques influence the flexural and shear performance of GFRP laminates. The composite materials were produced by integrating nonwoven glass tissues with woven glass fabrics, along with single and hybrid nanoscale fillers. Silica (SiO₂) and carbon (C) nanoparticles at different weight fractions were selected as nano-reinforcements for their cost-effectiveness. Seven composite variants were made by hand lay-up, including an unmodified GFRP reference and six hybrid configurations. Sonication and magnetic stirring methods were used to disperse nanoparticles in the epoxy matrix uniformly. Flexural performance was assessed by the three-point flexural test, while shear performance was assessed using the short beam shear and Iosipescu tests to measure both in-plane and interlaminar shear strength. When compared to the unmodified GFRP reference, samples with 0.5 wt% carbon black showed better shear and flexural performance. Hybrid reinforcement using 0.25 wt% carbon black combined with 0.25 wt% silica achieved the highest flexural strain increase (21%) and an 8% gain in flexural strength. This indicates improved ductility without compromising shear performance. However, higher concentrations of hybrid fillers negatively affect mechanical behavior.