24 March 2020 in IEEE Access
The exploration of deep and subtle oil and gas reservoirs is currently an important means of increasing production in older oil fields. How to effectively identify weak signals with noise is a common problem faced in such reservoirs. Especially for deep seismic reflection data, the application of traditional denoising methods is limited due to the weak energy and small difference frequency band between the effective signals and the noise. A novel method of noise attenuation for weak seismic signals based on compressed sensing and CEEMD (complementary ensemble empirical mode decomposition) was proposed in this work. This method consists of three steps: First, the CEEMD algorithm, a time-frequency analysis method, was introduced into the classic CS (compressed sensing) denoising method to overcome the nonadaptability of CS. CEEMD decomposed the raw seismic signals into sets of IMFs (finite intrinsic mode functions). The IMFs with noise were reconstructed and denoised by CS. In the second step, an enhancement operator was introduced into the penalty term to ensure that the effective signals could be extracted. Finally, the OMP algorithm is adopted to reconstruct the seismic weak signal to prevent the iterative threshold method from damaging weak effective signals. It was demonstrated through the synthetic seismic record and the field seismic data that (a) the CS method can identify the weak signals submerged in the noise by selecting the basic function that is most similar to the effective signals, but it cannot adaptively suppress the high frequency and high wavenumber noise of the complex seismic records; (b) the proposed method overcome the non-adaptability of CS and enhance the edge information described by the curved wave rather than the noises, as a result, the high frequency noise is suppressed while the middle/low frequency noise and weak effective signals are also effectively separated.
13 October 2020 in IEEE Access
In seismic exploration, matching pursuit (MP), which decomposes wavelets based on best signal matching, can not only extract accurate frequency information, but also can pick up the strong amplitudes of possible bright spots adaptively according to the threshold or iteration control. RGB (Red-Green-Blue) blending technique of spectral bands can make full use of the information of all frequency bands, which can reflect the general frequency changes of seismic data reducing the interpretation ambiguity. Therefore, in order to improve the precision of interpretation based on bright spot technique, the authors take both amplitude and frequency into account and propose a new approach for hydrocarbon identification by combining both methods. First, we choose the decomposed wavelets of strong amplitudes related to hydrocarbons in MP algorithm to predict the possible bright spots, so as to remove the effect of unrelated reflections in the bright spots interpretation. Then, RGB blending technique is used to the low-, mid-, and high-frequency spectral bands of the bright spot prediction section to assist for the hydrocarbon identification. Finally, the validity of the method is verified by both the model and field data tests. Results demonstrate that the proposed method can improve the precision of hydrocarbon identification, and reduce the interpretation ambiguity of the reservoirs.
1 September 2020 in Geophysics
The migration of multiples can provide complementary information about the subsurface, but crosstalk artifacts caused by the interference between different-order multiples reduce its reliability. To mitigate the crosstalk artifacts, least-squares reverse time migration (LSRTM) of multiples is suggested by some researchers. Multiples are more affected by attenuation than primaries because of the longer travel path. To avoid incorrect waveform matching during the inversion, we propose to include viscosity in the LSRTM implementation. A method of LSRTM of multiples is introduced based on a viscoacoustic wave equation, which is derived from the generalized standard linear solid model. The merit of the proposed method is that it not only compensates for the amplitude loss and phase change, which cannot be achieved by traditional RTM and LSRTM of multiples, but it also provides more information about the subsurface with fewer crosstalk artifacts by using multiples compared with the viscoacoustic LSRTM of primaries. Tests on sensitivity to the errors in the velocity model, the Q model, and the separated multiples reveal that accurate models and input multiples are vital to the image quality. Numerical tests on synthetic models and real data demonstrate the advantages of our approach in improving the quality of the image in terms of amplitude balancing and signal-to-noise ratio.
17 August 2022 in IEEE Transactions on Geoscience and Remote Sensing
Internal multiples bring great challenges for conventional seismic data imaging and interpretation, in which primaries only are regarded as signals. It is of great importance to suppress the internal multiples before conventional imaging, which is computationally expensive. Considering that internal multiples are also real reflections from the underground interfaces and reverse time migration (RTM) can realize the imaging of multiples. Instead of suppression before imaging, we propose to do the joint imaging of primaries and internal multiples based on RTM. However, the artifacts caused by the internal multiples should be suppressed to guarantee the precision. First, the imaging condition based on up-going and down-going extrapolated wavefield separation is introduced to improve the imaging accuracy. Then, the generation mechanism of image artifacts is analyzed, it concludes that nonphysical wave paths caused by the missing boundary wavefields under the surface result in the infidelity reversed-time backward-extrapolation, which is the main reason for the artifacts. Next, we propose to apply the modeling boundary wavefields with a match based on pseudomultichannel matching filter to compensate the missing boundary wavefields, which can avoid the image artifacts and realize high-precision joint imaging. Finally, the feasibility and effectiveness of the proposed method are verified by numerical examples and field data.
1 November 2017 in Geophysics
Multiples are usually regarded as noise in conventional seismic data processing. However, multiples are also real reflections from structural interfaces in the subsurface. Compared with primaries, multiples usually provide more balanced illumination and contain more structural information because of the smaller reflection angles and longer wavepaths. Instead of multiple suppression, multiple imaging has attracted increasingly more attention in recent years. The most commonly used migration method for multiples is performed by replacing the source wavelet with recorded data and using separated multiples as the receiver record. Then, the image of the multiples is obtained by the application of the crosscorrelation imaging condition, which is widely used in conventional migration. However, during the imaging procedure, events are matched based on their propagation times only. Crosscorrelation of unrelated events leads to heavy crosstalk, and image artifacts are introduced in the image of multiples. To overcome this shortcoming, we have introduced the stereographic imaging condition for the one-way wave-equation migration of multiples. By adding a local-slope constraint (the local slope of the extrapolated wavefields at every position and time), the stereographic imaging condition takes the local spatial coherence of the extrapolated wavefields into account. Events can be matched based not only on the propagating times but also the local slopes. Therefore, crosstalk artifacts caused by the interference of unrelated events can be efficiently suppressed. Furthermore, to improve the computational accuracy and efficiency of our approach, plane-wave destructors are introduced to estimate the reflector slopes. In this way, the need for excessive loops over the local slopes in the [ ]-[ ] domain during application of the stereographic imaging condition can be avoided by selecting the local slopes in a proper range. Better migration results of multiples are obtained in numerical tests, which verify the feasibility and effectiveness of our approach.
26 May 2020 in IEEE Access
Multiple reflections contain abundant structural information about the subsurface because of their smaller reflection angles and wider coverage. Multiple imaging has increasingly attracted attention. However, the imaging of multiples first needs to separate the multiples, which is a time-consuming and high-cost job. Therefore, the simultaneous imaging of primaries and multiples, which can make good use of multiple reflections with no need for multiple separation, has increasingly attracted attention. However, there are still some challenges to the conventional method, including wavelet selection and image artifacts suppression. In this paper, an improved method of the simultaneous imaging of primaries and multiples is proposed by introducing two creative strategies. First, considering that the wavelet, which is usually estimated by signal analysis under certain assumptions, is crucial to the simultaneous imaging, we propose to estimate the wavelet by iterative SRME (surface-related multiple elimination) using the original data containing multiples based on wave equation theory instead of signal analysis. Second, the stereographic imaging condition is introduced to suppress the crosstalk artifacts in the image. According to the numerical examples and field data test, the feasibility and effectiveness of our approach is verified.