Structural colors originate by constructive interference following reflection and scattering of light from nanostructures with periodicity comparable to visible light wavelengths. Bright and noniridescent structural colorations are highly desirable. Here, we demonstrate that bright noniridescence structural coloration can be easily and rapidly achieved from suspended two-dimensional nanosheets of a clay mineral. We show that brightness is enormously improved by using double clay nanosheets, thus optimizing the clay refractive index that otherwise hampers structural coloration from such systems. Intralayer distances, and thus the structural colors, can be precisely and reproducibly controlled by clay concentration and ionic strength independently, and noniridescence is readily and effortlessly obtained in this system. Embedding such clay-designed nanosheets in recyclable solid matrices could provide tunable vivid coloration and mechanical strength and stability at the same time, thus opening a previously unknown venue for sustainable structural coloration.
Exploiting the full potential of layered materials for a broad range of applications requires delamination into functional nanosheets. Delamination via repulsive osmotic swelling is driven by thermodynamics and represents the most gentle route to obtain nematic liquid crystals consisting exclusively of single-layer nanosheets. This mechanism was, however, long limited to very few compounds, including 2:1-type clay minerals, layered titanates, or niobates. Despite the great potential of zeolites and their microporous layered counterparts, nanosheet production is challenging and troublesome, and published procedures implied the use of some shearing forces. Here, we present a scalable, eco-friendly, and utter delamination of the microporous layered silicate ilerite into single-layer nanosheets that extends repulsive delamination to the class of layered zeolites. As the sheet diameter is preserved, nematic suspensions with cofacial nanosheets of ≈9000 aspect ratio are obtained that can be cast into oriented films, e.g., for barrier applications.
The effect of humidity on the ionic transport in the amorphous phase of poly(ethylene oxide) thin films has been studied by local dielectric spectroscopy. We explored a controlled humidity range between 15% RH and 50% RH. AFM-based local dielectric imaging allowed the thin film topography and the corresponding dielectric contrast maps to be obtained simultaneously. No humidity effect on the film topography was observed whereas large variation of the dielectric signal could be detected. In addition, we observed a clear dielectric contrast in different locations on the thin film surface. At selected regions with high contrast in the dielectric maps, we performed nanoDielectric Spectroscopy (nDS) measurements covering the frequency range from 5 Hz to 100 kHz. By modeling these spectroscopy results, we quantified the conductivity of the amorphous phase of the semicrystalline poly(ethylene oxide) films. The crystalline fraction of the PEO thin films was extracted and found to be about 36%, independently of humidity. However, the average conductivity increased by a factor of 25 from 2 × 10−10 to 5 × 10−9 S cm−1, by changing environmental humidity in the explored % RH range.
Preparing halide perovskite films by solvent‐free, powder‐based processing approaches currently attracts more and more attention. However, working solar cells employing dry, powder‐based halide perovskite thin films, have not been demonstrated so far. Herein, perovskite solar cells are presented where the absorber layer is prepared by transferring readily synthesized perovskite powders into a compact thin film using a fully dry‐powder‐processing concept. Compact thin films are deposited via an optimized powder aerosol deposition (PAD) process. Pressing at 120 °C further improves the morphology and the optoelectronic film properties. Integrating the perovskite films in a solar cell configuration results in fully working devices, with champion power conversion efficiencies of >6%. While the (optoelectronic) properties of the PAD‐processed films are found to be comparable with their solution‐processed counterparts, investigations of the solar cell stack suggest deterioration of the electron‐transport layer properties due to the PAD process, and the presence of hydrates at the perovskite surface to be important factors that contribute to the limited solar cell efficiency. Herein, perspectives to overcome the identified limitations are outlined, emphasizing the high potential and realizability of efficient perovskite solar cells based on dry‐powder‐processing approaches in the future.