This study aims to compare different hyperspectral imaging devices and identify their suitability for in-situ color and lighting research. Three hyperspectral cameras were compared for radiometric, photometric, and colorimetric accuracy. The visual quality of the images obtained with each device was also evaluated to test their suitability for psychophysical experiments on color perception. The accuracies were evaluated for LED sources with correlated color temperatures ranging from 2351 K to 6922 K. The hyperspectral cameras tested were found to have acceptable radiometric accuracies for chromatic content and different photometric and colorimetric accuracies. It was also identified that a good radiometric/photometric accuracy does not necessarily indicate a good colorimetric accuracy for the same device and color. It depends on the light sources and color patches, thus highlighting the need to identify the reproduction accuracy of every test device methodically. This accuracy study thus describes a formal layout for the characterization of hyperspectral imaging devices using identifiable error metrics.
The Daylight Illuminant D65, a standardised reference light source in design and research with a colour temperature of 6500 K, is often used to describe the colour of the daylight. However, it represents the colour of an overcast sky, failing to capture the variability and richness of actual daylight, particularly the blue of clear skies. Recent research shows that both sunlight and skylight significantly influence our mood, perception and physiological responses. The colour of daylight is influenced by factors like sun position, weather conditions, as well as geographical location. To address these variations, researchers are collecting worldwide spectral daylight measurements, emphasising the need for localised spectral reference data to appropriately represent daylight in different locations.
Color Acceptability is a complex phenomenon. Contrary to perceptibility, color acceptability is defined as the level of color difference that is considered under the limit of preferred color reproduction on two media. A system comprising two automotive OLED and LCD displays was used in this experiment. A previous study (presented at [1]) by the authors had identified this limit for a daylight scenario where an external illumination of 3000 Lux at 5300K was illuminating the surface of the displays. In this study a night-time driving scenario was simulated with a projector light source illuminating the displays at 50 lux and 1318K. Statistical analysis is used to quantify statistically significant differences between various conditions. _x005F_x000D_ Introduction
The sunglass industry has seen a major development in the past few years, though without the development of sunglass simulation tools for the wearers. This study describes a protocol to accurately simulate sunglass filtered vision using hyperspectral imaging and colour appearance model. The use of hyperspectral imaging ensures that the spectral transmittances of the sunglasses can be applied to the spectral radiances of the target scene. This filtered hyperspectral data can then be converted into a colour image using CIE XYZ tristimulus values and image colour appearance model (iCAM06). The study also identifies the protocol for the testing of these filtered images through psychophysical experiments and formulates the key parameters for testing. Furthermore, the study also categorizes the acquisition parameters for accurate and fast application of sunglasses on hyperspectral images. Objective testing on the optimized hyperspectral data revealed a reduction of data size by four times, without any loss of colorimetric accuracy. The study lays out a clear path for the future execution of psychophysical experiments to validate the accuracy of reproduction for these simulated images.
In recent years, the spectral properties of solar radiation and daylight have become increasingly important in lighting design and research, and various approaches to implement these have been applied. This paper proposes to modify and adapt the CIE reconstruction method, a procedure developed in the early 1960s to define standardised spectral power distributions (SPDs) of daylight, for this purpose. The CIE D Illuminants resulting from the reconstruction procedure are widely used for standardisation purposes but are based on a smaller number of measurements and do not consider geographical, seasonal and diurnal variations. In order to be able to use the CIE reconstruction method specifically in daylight planning, research and application, a technical committee of the CIE has launched a worldwide measurement campaign to collect spectral daylight measurements. The aim of the committee is to formulate a customised reconstruction method that more accurately reflects the local SPDs of daylight. This paper contributes to the discourse on the improvement of daylight estimation methods and emphasises the importance of accurate daylight data in various scientific and practical contexts.