Seunghee A. Oh

Seunghee A. Oh

Auto-generated profile, based on publicly available information

Seunghee A. Oh

Department of Materials Science and Engineering, Carnegie Mellon University, Pittsburgh, USA

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 August 2021 in Materials Research Letters
Verified
Journal Article
Open access
SOSeunghee A. Oh
Seunghee A. Oh
RLRachel E. Lim
Rachel E. Lim
JAJoseph W. Aroh
Joseph W. Aroh
ACAndrew C. Chuang
Andrew C. Chuang
BGBenjamin J. Gould
Benjamin J. Gould
ARAnthony D. Rollett
Anthony D. Rollett
The microstructures of Ti-6Al-4V following laser processing depend primarily on the phase transformation of β to α, but their development is constrained by the rapidly changing temperature in the small fusion zone. In-situ synchrotron X-ray diffraction was utilized to probe the rapid phase evolution in single melt tracks with high angular and temporal resolution. Both fully martensitic and mixed α+α′+β microstructures were confirmed by microscopy. Cooling rates were inferred from the lattice parameter history and complementary thermal simulation. It was found that the threshold cooling rate for fully martensitic transformation is in the range between 2900 and 6500°C/s. IMPACT STATEMENT High-speed synchrotron X-ray diffraction during operando laser processing suggests a new threshold between martensitic and diffusional phase transformation in Ti-6Al-4V occurring at higher cooling rates than previously reported.

17 November 2020 in JOM
Verified
Journal Article
Closed access
PDF file
SOSeunghee A. Oh
Seunghee A. Oh
RLRachel E. Lim
Rachel E. Lim
JAJoseph W. Aroh
Joseph W. Aroh
ACAndrew C. Chuang
Andrew C. Chuang
BGBenjamin J. Gould
Benjamin J. Gould
ARAnthony D. Rollett
Anthony D. Rollett

23 April 2024 in Communications Materials
Verified
Journal Article
Open access
PDF file
SOSeunghee A. Oh
Seunghee A. Oh
JAJoseph W. Aroh
Joseph W. Aroh
NLNicholas Lamprinakos
Nicholas Lamprinakos
CCChihpin Andrew Chuang
Chihpin Andrew Chuang
ABAshley N. Bucsek
Ashley N. Bucsek
ARAnthony D. Rollett
Anthony D. Rollett
Martensite, α‘, commonly appears in Ti-6Al-4V upon rapid cooling from above the β-transus temperature. It is known that α‘ decomposes into α and β at high temperatures but well below the β-transus temperature. Here, we study the decomposition of martensitic Ti-6Al-4V under rapid laser heating, employing in situ synchrotron X-ray diffraction. A comparison is made with post-annealed Ti-6Al-4V under heating to elucidate changes without martensite decomposition. The fast acquisition of X-ray diffraction data at 250 Hz temporally resolves the decomposition process initiated by annihilating dislocations in α‘. The recovery process is accompanied by structural changes in martensite, followed by the phase transformation to β. Thermal profiles estimated from the lattice parameter data reveal the influence of heating rates and dislocation densities on the decomposition process. Throughout the analysis of the diffraction profiles with respect to estimated temperature, we propose a straightforward method for approximating the initiation temperature of martensite decomposition.

29 April 2025 in Nature Communications
Verified
Journal Article
Open access
PDF file
SOSeunghee Oh
Seunghee Oh
YJYuefeng Jin
Yuefeng Jin
SLSangwon Lee
Sangwon Lee
WLWenxi Li
Wenxi Li
KGKen Geauvreau
Ken Geauvreau
ABAshley Bucsek
Ashley Bucsek
Three-dimensional x-ray diffraction (3DXRD), a rotating x-ray diffraction technique, is a powerful tool for studying the micromechanical behavior of polycrystalline materials, capable of measuring the volume, position, orientation, and strain of thousands of grains simultaneously. However, its application has been historically limited to synchrotron facilities. Here, we present the first demonstration of laboratory-scale 3DXRD (Lab-3DXRD) using a liquid-metal-jet source. Lab-3DXRD achieves accuracy comparable to synchrotron-based 3DXRD, as validated against laboratory diffraction contrast tomography (LabDCT) and synchrotron-3DXRD. Over 96% of the grains detected with Lab-3DXRD are cross-validated, particularly for coarse grains (> ~60 μm), while the results suggest that finer grains should be accessible by taking advantage of high-efficiency detectors. We further demonstrate that its sensitivity to finer grains is enhanced by incorporating pre-characterization into the analysis. This study establishes Lab-3DXRD as a practical alternative to synchrotron techniques, making 3DXRD accessible to a wider range of academic and industrial researchers.

15 May 2025 in Acta Materialia
Verified
Journal Article
Open access
SOSeunghee Oh
Seunghee Oh
RLRachel Lim
Rachel Lim
ACAndrew Chihpin Chuang
Andrew Chihpin Chuang
BGBenjamin Gould
Benjamin Gould
ABAshley Bucsek
Ashley Bucsek
ARAnthony Rollett
Anthony Rollett