Azzam S. Salman

Azzam S. Salman

Auto-generated profile, based on publicly available information

Azzam S. Salman

University of South Carolina, Columbia, SC

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2020 in International Communications in Heat and Mass Transfer
Verified
Journal Article
Closed access
ATAmitav Tikadar
Amitav Tikadar
TPTitan C. Paul
Titan C. Paul
SOSaad K. Oudah
Saad K. Oudah
NANabeel M. Abdulrazzaq
Nabeel M. Abdulrazzaq
ASAzzam S. Salman
Azzam S. Salman
JKJamil A. Khan
Jamil A. Khan

1 April 2019 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
ASAzzam S. Salman
Azzam S. Salman
NANabeel M. Abdulrazzaq
Nabeel M. Abdulrazzaq
SOSaad K. Oudah
Saad K. Oudah
ATAmitav Tikadar
Amitav Tikadar
NANoble C. Anumbe
Noble C. Anumbe
JKJamil A. Khan
Jamil A. Khan

1 May 2019 in Applied Thermal Engineering
Verified
Journal Article
Closed access
ATAmitav Tikadar
Amitav Tikadar
SOSaad K. Oudah
Saad K. Oudah
TPTitan C. Paul
Titan C. Paul
ASAzzam S. Salman
Azzam S. Salman
AMA.K.M.M. Morshed
A.K.M.M. Morshed
JKJamil A. Khan
Jamil A. Khan

1 November 2018 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
ATAmitav Tikadar
Amitav Tikadar
UNUmair Najeeb
Umair Najeeb
TPTitan C. Paul
Titan C. Paul
SOSaad K. Oudah
Saad K. Oudah
ASAzzam S. Salman
Azzam S. Salman
JKJamil A. Khan
Jamil A. Khan

3 November 2017
Verified
Conference Paper
Closed access
PDF file
ASAzzam S. Salman
Azzam S. Salman
JKJamil A. Khan
Jamil A. Khan
Experiments were conducted in a closed loop spray cooling system working with deionized water as a working fluid. This study was performed to investigate the effect of the spraying parameters, such as Sauter mean diameter (SMD), the droplet velocity, and the residual velocity on the spray cooling heat transfer in the non-boiling region. Thermal effects on plain and modified surfaces with circular grooves were examined under different operating conditions. The inlet pressure of the working fluid was varied from 78.6 kPa to 183.515kPa, and the inlet temperature was kept between 21–22 °C. The distance between the nozzle and the target surface 10 mm. The results showed that increasing the coolant inlet pressure increases the droplet velocity and the number of droplets produced while decreasing the droplet size. As a consequence of these changes, increasing inlet pressure improved the heat transfer characteristics of both surfaces.

9 July 2017
Verified
Conference Paper
Closed access
PDF file
ASAzzam S. Salman
Azzam S. Salman
JKJamil A. Khan
Jamil A. Khan
An experimental study was conducted in a closed loop spray cooling system working with deionized water as a cooling medium, to investigate the effects of surface modification on the spray cooling heat transfer enhancement in the single-phase region. Plain copper surface with diameter 1.5 cm and an enhanced surface with circular grooves were tested under different operating conditions. The volumetric flow rate of the coolant ranged from 115 mL/min to 177 mL/min., and the water inlet temperature was kept between 21–23 °C. Also, the distances between the nozzle and the target surface were varied at 8, 10, and 12 mm respectively. The results show that the distance between the nozzle and the target surface did not have a significant effect on the heat transfer performance for the low flow rates, while it has a slight effect on high flow rates for both surfaces. Also, increasing the liquid volumetric flow rate increases the amount of heat removed, and the heat transfer coefficient for both surfaces. Moreover, the maximum enhancement ratios achieved were 23.4% and 31% with volumetric flow rates of 153 mL/min, and 177 mL/min respectively.