Already, several technologies of polycrystalline thin‐film photovoltaic materials have achieved certified record small‐cell power conversion efficiencies exceeding 22%. They are CdTe, Cu(In,Ga)(S,Se)2 (CIGS), and metal halide perovskite (PSC), each named after the light-absorbing semiconductor material. Thin-film solar cells and modules require very little active material due to their very high absorption coefficient. Efficient production methods with low materials waste, moderate temperatures, attractive cost structures, and favorable energy payback times will play a strong role in market development as thin-film technologies reach full maturity, including mass production and the standardization of production machineries. In fact, the first two technologies have already been developed up to the industrial scale with a market share of several GW. In this review article, we outline similarities and differences between these high‐efficiency thin‐film technologies from both the materials and the industrial point of view. We address the materials characteristics and device concepts for each technology, including a description of recent developments that have led to very high efficiency achievements. We provide an overview of the CIGS industry players and their current status. The newcomer PSC has demonstrated its potential in the laboratory, and initial efforts in industrial production are underway. A large number of laboratories are experimenting through a wide range of options in order to optimize not only the efficiency but also stability, environmental aspects, and manufacturability of PSC. Its high efficiency and its high bandgap make PSC particularly attractive for tandem applications. An overview of all these topics is included here along with a list of materials configurations.
29 July 2013 in Physica Status Solidi (RRL) – Rapid Research Letters
The diffusion of the heavy alkali element rubidium (Rb) in Cu(In,Ga)Se2 (CIGS) layers was investigated over a temperature range from 148 °C to 311 °C by outdiffusion from a rubidium fluoride layer. The diffusion profiles were measured by secondary ion mass spectrometry. By using CIGS layers with different grain sizes, diffusion along grain boundaries could be distinguished from diffusion into the grain interior. Rb was found to diffuse from the CIGS surface along grain boundaries but also within the grain bulk. Based on these data, the slower diffusion coefficient in the volume can be described by the Arrhenius equation DV (Rb) = 3.8·10−8 exp(−0.44 eV/kBT) cm2 s−1 and the fast diffusion along the grain boundaries by DGB (Rb) = 5.7·10−9 exp(−0.29 eV/kBT) cm2 s−1. Further, the effect of Na on Rb diffusion was investigated by comparing Rb diffusion into a Na-containing CIGS layer in contrast to Rb diffusion into an alkali-free CIGS layer. This comparison revealed some aspects of the ion exchange mechanism. Finally, the effect of Rb on the solar cell parameters of CIGS thin-film solar cells was investigated. Rb was found to enhance the open-circuit voltage, the fill factor, and charge carrier density in a similar manner as observed for potassium and sodium.
10 April 2018 in ACS Applied Materials & Interfaces
Alternative buffer layers in CIGSe are deposited mainly using chemical bath deposition because of its benefits like simplicity, good film quality and surface/step coverage. All the layers in CIGSe cell stack such as back contact, absorber and window layers are deposited by vacuum–deposition methods such as coevaporation, sputtering, and sometimes thermal evaporation, except for the buffer layer. Therefore, in the present work we demonstrate the feasibility to deposit In2S3 by RF magnetron sputtering reaching cell efficiencies of 13.6%, which is the highest value available for sputtered In2S3 in literature to date. Absorber surface damage and nonuniform buffer layer thickness are the primary limitations when using sputtering, and hence need to be eliminated for reaching reasonable cell efficiencies. We studied the extent of sputter induced damage on CIGSe absorber as well as the sputtering– and annealing–induced intermixing phenomenon at the In2S3/Cu(In,Ga)Se2 interface at the subnanometer level using atom probe tomography. We have also shown that a post deposition annealing not only significantly improves the crystallinity of In2S3, but also recovers the surface damage caused by sputter‐induced intermixing resulting in an improved p‐n Junction quality (as shown by the electron beam induced current investigations), and substantially improves cell efficiency. The present work opens a new way for designing efficient and industry–compatible CIGSe cells using sputter–deposited Cd‐free buffer layers. Moreover, this work clearly demonstrates that this novel and fully vacuum–deposited CIGSe cell meets the standard requirements, in terms of chemistry, structure, and electrical performance of a working cell for the PV industry.
The impact of sodium on the electrical properties of Cu(In,Ga)Se2 (CIGS) thin films and corresponding solar cells was investigated by preparing nearly alkali-free CIGS layers and doping them with different Na amounts via NaF post-deposition treatment (PDT) at temperatures between 110 and 400 °C. The mean Na concentrations in the CIGS layers ranged from 0.1 to 400 ppm. Sodium was found also in the grain interior even for the lowest PDT temperature. All samples were subjected to extensive electrical characterization: current–voltage, capacitance profiling, conductivity, steady-state, and transient capacitance spectroscopy. A continuous increase in open-circuit voltage VOC and fill factor FF, an accompanying increase in hole density and mobility, and a decrease in secondary barriers responsible for the distortion of current–voltage characteristics were observed with increasing sodium content. An abrupt change in defect spectra and a dominant transport mechanism was found for PDT temperatures T(PDT) of ≥150 °C. We attribute a further improvement in VOC observed above 150 °C PDT temperature to the reduced concentration of recombination centers with increased sodium content. An explanation of both gradual evolution and the abrupt change is proposed based on passivation of grain boundaries and interfaces by sodium.