Nazih Mechbal

Nazih Mechbal

Auto-generated profile, based on publicly available information

Nazih Mechbal

Arts et Metiers ParisTech, PIMM UMR CNRS, Paris, France

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 August 2016 in Structural Health Monitoring
Verified
Journal Article
Closed access
CFC Fendzi
C Fendzi
MRM Rébillat
M Rébillat
NMN Mechbal
N Mechbal
MGM Guskov
M Guskov
GCG Coffignal
G Coffignal
This paper presents a temperature compensation method for Lamb wave structural health monitoring. The proposed approach considers a representation of the piezo-sensor signal through its Hilbert transform that allows one to extract the amplitude factor and the phase shift in signals caused by temperature changes. An ordinary least square (OLS) algorithm is used to estimate these unknown parameters. After estimating these parameters at each temperature in the operating range, linear functional relationships between the temperature and the estimated parameters are derived using the least squares method. A temperature compensation model is developed based on this linear relationship that allows one to reconstruct sensor signals at any arbitrary temperature. The proposed approach is validated numerically and experimentally for an anisotropic composite plate at different temperatures ranging from 16°C to 85°C . A close match is found between the measured signals and the reconstructed ones. This approach is interesting as it needs only a limited set of piezo-sensor signals at different temperatures for model training and temperature compensation at any arbitrary temperature. Damage localization results after temperature compensation demonstrate its robustness and effectiveness.

10 March 2015 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
CFC Fendzi
C Fendzi
NMN Mechbal
N Mechbal
MRM Rébillat
M Rébillat
MGM Guskov
M Guskov
GCG Coffignal
G Coffignal
This article focuses on Bayesian Lamb wave-based damage localization in structural health monitoring of anisotropic composite materials. A Bayesian framework is applied to take account of uncertainties from experimental time-of-flight measurements and angle-dependent group velocity within the composite material. An original parametric analytical expression of the direction dependence of group velocity is proposed and validated numerically and experimentally for anisotropic composite and sandwich plates. This expression is incorporated into time-of-arrival (ellipse-based) and time-difference-of-arrival (hyperbola-based) Bayesian damage localization algorithms. This way, the damage location and the group velocity profile are estimated jointly and a priori information is taken into consideration. The proposed algorithm is general as it allows us to take into account uncertainties within a Bayesian framework, and to model effects of anisotropy on group velocity. Numerical and experimental results obtained with different damage sizes or locations and for different degrees of anisotropy validate the ability of the proposed algorithm to estimate both the damage location and the group velocity profile as well as the associated confidence intervals. Results highlight the need to consider for anisotropy in order to increase localization accuracy, and to use Bayesian analysis to quantify uncertainties in damage localization.

1 October 2013 in Journal of Mechanisms and Robotics
Verified
Journal Article
Closed access
PDF file
SVSébastien Voisembert
Sébastien Voisembert
NMNazih Mechbal
Nazih Mechbal
ARAlain Riwan
Alain Riwan
AAAméziane Aoussat
Améziane Aoussat
The aim of this paper is to present the design of a new long-range robotic arm based on an inflatable structure. Inflatable robotics has potential for improved large payload-to-weight ratios, safe collision, and inspection in areas inaccessible to human beings as in nuclear plants. The robot presented here is intended to operate inspection or maintenance missions in critical installation taking care to not collide with its environment. It is made with innovative inflatable joints and an original actuation system. Prototypes of this inflatable manipulator were constructed using two different manufacturing procedures. Using ls-dyna nonlinear dynamic finite element modeling we have numerically analyzed the specific geometry and dynamical behavior of the resulting joints. The simulations have given insight into understanding the joint bending process and have revealed guidance for optimizing the conception.

1 October 2014 in Mechanical Systems and Signal Processing
Verified
Journal Article
Closed access
MRMarc Rébillat
Marc Rébillat
RHRafik Hajrya
Rafik Hajrya
NMNazih Mechbal
Nazih Mechbal

1 July 2017 in Composite Structures
Verified
Journal Article
Closed access
MGMeriem Ghrib
Meriem Ghrib
LBLaurent Berthe
Laurent Berthe
NMNazih Mechbal
Nazih Mechbal
MRMarc Rébillat
Marc Rébillat
MGMikhail Guskov
Mikhail Guskov
NBNas Bedreddine
Nas Bedreddine

1 May 2011
Verified
Conference Paper
Closed access
SVS. Voisembert
S. Voisembert
ARA. Riwan
A. Riwan
NMN. Mechbal
N. Mechbal
ABA. Barraco
A. Barraco
Inflatable structures are already used in robotics to build stiff and light inflatable links. Moreover, those links are compliant and they can be safely used in robots interacting with critical installations. Nevertheless, until now, linkages with an inflatable structure have always been composed of independent inflatable links separated by joints. But the joints are heavier, less stiff, or less safe than the inflatable links. So in this paper, we present a new design of inflatable robots with joints having similar mechanical characteristics as the links. A first prototype, a model of the joints and some experimental validation will also be presented.