Andrzej Tomczyk

Andrzej Tomczyk

Auto-generated profile, based on publicly available information

Andrzej Tomczyk

Rzeszów University of Technology

Research Focus & Metrics

Academic Career Length

37Years (1990-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 March 2013 in Solid State Phenomena
Verified
Journal Article
Closed access
PDF file
GKGrzegorz Kopecki
Grzegorz Kopecki
ATAndrzej Tomczyk
Andrzej Tomczyk
Pawel RzucidloPawel Rzucidlo
Pawel Rzucidlo
The article presents a measurement system for a micro UAV designed at the Department of Avionics and Control Systems of Rzeszów University of Technology. Since the project is based on earlier projects, e.g.[[[[1[[[1, the introduction begins with their short presentation [they are mentioned in the introduction firs. Then, the current project is discussed. The major objective of the project is to create a miniature autopilot cooperating with navigation units, data transmission units and measurement units. The system is based on Polish technological solutions. The autopilot is designed as a single unit, however the system is open and it allows you to use different elements. The system development is also possible. In-flight testing will be realized with the use of two unmanned flying platforms equipped with an electrical engine and a piston engine. The total mass of the platforms is 5 kg and 25 kg respectively. The article presents the structure of the control and navigation system and then, the structure of the measurement system. The measurement units consist of a GPS receiver, an attitude and heading reference system (AHRS) and an air data computer (ADC). Similar configuration is used in other micro UAV solutions, such as Micropilot or Kestrel. Then, algorithms of the measurement system are described. Navigation is based on GPS data with a DGPS (Differential GPS) advanced module. If the measurement information is complete, GPS data are used to correct measurements from other units. The system estimates wind disturbances and calculates accelerometers errors. In the case of missing GPS signals implementation of low-cost sensors may lead to significant measurement errors, and hence navigation only by means of the INS is impossible. In such a case, navigation is realized with the use of an inertial navigation system (INS), the magnetic heading measurement and ADC. AHRS unit algorithms use quaternion algebra for attitude calculation. For correction, complementary filtering is implemented [, [. The correction signal for the attitude (pitch and roll angles) is calculated with the use of acceleration measurements. Measurements of accelerations and yaw rates are used for the correction switching mechanism, since in dynamic states signals calculated from accelerations cannot be used for correction. Heading is corrected by means of magnetic heading measurement. ADC algorithms are based on typical aerodynamic dependences.

4 September 2009 in Aircraft Engineering and Aerospace Technology
Verified
Journal Article
Closed access
PCPeter Chudý
Peter Chudý
ATAndrzej Tomczyk
Andrzej Tomczyk
Pawel RzucidloPawel Rzucidlo
Pawel Rzucidlo
Purpose: The purpose of this paper is to describe the general idea, design, and implementation of control system for general aviation aircraft which reduces pilot workload.Design/methodology/approach: Proposed indirect flight control system framework is intended to simplify piloting, reduce pilot workload, and allow low‐end general aviation aircraft to operate under deteriorated meteorological conditions. Classical control theory is used for the design of the flight control laws. Although not inherently robust, controllers with classical control logic are made sufficiently stable using a correct and updated controller structure.Findings: Despite controversies between perception of a modern manned aerial vehicle and limitations imposed by legacy airworthiness codes it is shown that a pilot workload reducing system can be successfully implemented onboard of a low‐end general aviation aircraft.Research limitations/implications: Hi‐level control laws and optimization of handling qualities can lead to unfavourable and unpredictable forms of man‐machine interactions, e.g. pilot‐induced oscillations.Practical implications: General aviation aircraft are mostly flown by a single pilot, who could benefit from an intelligent system or “virtual copilot” assisting in or supervising the aircraft's safe operation under any conditions. Aircraft with this capability represents a next step in the evolution that might ultimately lead to trajectory‐based free‐flight concept of aircraft operations.Originality/value: The paper introduces a safety enhanced digital flight control system on board small general aviation aircraft.

30 September 2004 in Aerospace Science and Technology
Verified
Journal Article
Closed access
ATAndrzej Tomczyk
Andrzej Tomczyk

1 November 2005 in Aerospace Science and Technology
Verified
Journal Article
Closed access
ATAndrzej Tomczyk
Andrzej Tomczyk

1 December 2003 in Aircraft Engineering and Aerospace Technology
Verified
Journal Article
Closed access
ATAndrzej Tomczyk
Andrzej Tomczyk
In this paper, results of the flight‐testing of an unmanned aerial vehicle (UAV) flight control system are presented. APC‐4 “SkyGuide” autonomous navigation and control system, designed and developed by the research team of the Department of Avionics and Control at Rzeszów University of Technology, has been tested. Properties of this flight control system, as well as selected results of the in‐flight tests conducted on board of the PZL‐110 “Koliber” aircraft, are presented. Results obtained confirm that design assumptions of the navigation and control system and research methodology have been appropriate and APC‐4 autopilot can be used on UAVs board.