3 June 2013 in International Journal of Control
This paper deals with proportional–integral–derivative (PID) controller design for nonlinear systems represented by local model networks. The proposed method is based on the concept of parallel distributed compensators where the scheduling of the local model network is adopted for the PID parameters. The proposed design method for nonlinear PID controllers considers closed-loop stability by means of a Lyapunov stability criterion as well as closed-loop performance. All PID parameters are determined by a multi-objective genetic algorithm (multiGA), which handles the trade-off between stability and performance. A simulation example demonstrates the effectiveness of the proposed method.
18 August 2020 in IEEE Transactions on Industrial Electronics
In this article, a new approach for combustion engine test bed system identification is presented. Modern engine test beds are used to reduce development time by utilizing them for hardware-in-the-loop tests. For highly accurate and close-to-reality tests, model-based controllers are deployed, which rely on precise models of the test bed. Hereby, the main challenge is the unknown, cyclic disturbance of the engine due to compression and combustion of the air-fuel mixture. These disturbances also occur when the throttle is kept at zero and have a big impact on the measurements. Therefore, parameter estimation is strongly impeded. A method for dealing with these disturbances and embed them into the identification procedure in a two-step fashion is presented in this contribution. Further advantages of this new approach are that a physical model is obtained, but prior knowledge of parameters is not necessary. Moreover, disassembling of the test bed to perform separate parameter estimation is not needed and hence, the time consumption of the procedure is kept low. Experimental results on a 4-cylinder diesel engine test bed prove the feasibility and effectiveness of the proposed concepts.
16 April 2021 in IEEE Open Journal of Industry Applications
Hardware-in-the-Loop tests have become a key factor in decreasing development time of various drive systems. In this context, high performance test beds, where feedback control plays a major role, are necessary to meet the demanding requirements such as real driving emissions in the automotive industry. Particularly for combustion engine test beds, periodic combustion strokes cause large oscillations in different measurement signals on engine test beds, which causes severe problems since conventional controllers try to compensate for these periodic disturbances. The control settings are a trade-off between fast reference tracking and undesirably strong disturbance rejection, which may compromise test results. An ordinary two-degree-of-freedom (2-DOF) control with flatness-based feedforward control produces relief in separating reference and disturbance behavior but cannot handle input constraints. Thus, a model predictive feedforward controller (MPFFC) in combination with the 2-DOF strategy is introduced for high-dynamic speed control in this contribution. The MPFFC generates optimal input and output trajectories, which respect constraints of the system. Fast reference tracking is achieved without the risk of falsification by high feedback. Comparisons between the proposed method, a simple feedback and a standard 2-DOF controller with a conventional flatness-based feedforward control are performed on a state-of-the-art 4-cylinder engine test bed. The experiments constitute a rare implementation of a MPFFC on a real system and demonstrate its capabilities of separating reference and disturbance response as well as taking advantage of certain situations to even further improve reference tracking speed.
16 February 2024 in IEEE Open Journal of Industry Applications
Power hardware-in-the-loop (PHIL) testing has become indispensable for the rapid, modular, and cost-saving development of automotive components. This paper focuses on PHIL tests composed of entire powertrains that exchange speed and torque signals with vehicle simulations. Previous studies pointed out the importance of promptly following the references from the virtual simulation environment to replicate realistic driving conditions and introduced control strategies to cope with the challenges associated with this setup. However, a comprehensive comparison of the different control strategies has not yet been carried out. To fill this gap, the concepts are first investigated in-depth in simulations and are then rigorously validated on a state-of-the-art powertrain test bed under highly dynamic driving scenarios, including full-braking. Furthermore, an improvement of existing shaft torque control approaches, which are mainly based on feedforward control, is proposed to better compete with the other methods. The proposed extension shows higher resilience to low accuracy of torque actuators, while the other concepts exhibit greater robustness against time delays. The results from the direct comparisons are summarized and allow the appropriate selection of control strategies for specific use cases.