Michael Delos Kass

Michael Delos Kass

Auto-generated profile, based on publicly available information

Michael Delos Kass

Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)

Research Focus & Metrics

Academic Career Length

32Years (1995-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 June 2020 in Energy & Fuels
Verified
Journal Article
Closed access
MKMichael D. Kass
Michael D. Kass
BABeth L. Armstrong
Beth L. Armstrong
BKBrian C. Kaul
Brian C. Kaul
RCRaynella Maggie Connatser
Raynella Maggie Connatser
SLSamuel Lewis
Samuel Lewis
DSDino Sulejmanovic
Dino Sulejmanovic

1 June 2010 in Catalysis Today
Verified
Journal Article
Closed access
JPJames E. Parks
James E. Parks
VPVitaly Prikhodko
Vitaly Prikhodko
JSJohn M.E. Storey
John M.E. Storey
TBTeresa L. Barone
Teresa L. Barone
SLSamuel A. Lewis
Samuel A. Lewis
SHShean P. Huff
Shean P. Huff

7 May 2001 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
MKMichael D. Kass
Michael D. Kass
JTJohn F. Thomas
John F. Thomas
JSJohn M. Storey
John M. Storey
NDNorberto Domingo
Norberto Domingo
JWJames Wade
James Wade
GKGlenn Kenreck
Glenn Kenreck
A certification diesel fuel and blends containing 10 and 15 volume % ethanol were tested in a 5.9-liter Cummins B Series engine. For each fuel blend, an 8-mode AVL test cycle was performed. The resulting emissions were characterized and measured for each individual test mode (prescribed combination of engine speed and load). These individual mode results are used to create a weighted average that is designed to approximate the results of the Heavy-Duty Transient Federal Test Procedure. The addition of ethanol was observed to have no noticeable effect on the emission of NOx but produced small increases in CO and HC. However, the particulate matter was observed to decrease 20% and 30% with the addition of 10% and 15% ethanol, respectively.

21 November 2022 in Environmental Science & Technology
Verified
Journal Article
Open access
SLShuyun Li
Shuyun Li
Eric C. D. TanEric C. D. Tan
Eric C. D. Tan
ADAbhijit Dutta
Abhijit Dutta
LSLesley J. Snowden-Swan
Lesley J. Snowden-Swan
MTMichael Richard Thorson
Michael Richard Thorson
THTroy R. Hawkins
Troy R. Hawkins
Renewable, low-carbon biofuels offer the potential opportunity to decarbonize marine transportation. This paper presents a comparative techno-economic analysis and process sustainability assessment of four conversion pathways: (1) hydrothermal liquefaction (HTL) of wet wastes such as sewage sludge and manure; (2) fast pyrolysis of woody biomass; (3) landfill gas Fischer-Tropsch synthesis; and (4) lignin-ethanol oil from the lignocellulosic ethanol biorefinery utilizing reductive catalytic fractionation. These alternative marine biofuels have a modeled minimum fuel selling price between $1.68 and $3.98 per heavy fuel oil gallon equivalent in 2016 U.S. dollars based on a mature plant assessment. The selected pathways also exhibit good process sustainability performance in terms of water intensity compared to the petroleum refineries. Further, the O and S contents of the biofuels vary widely. While the non-HTL biofuels exhibit negligible S content, the raw biocrudes via HTL pathways from sludge and manure show relatively high S contents (>0.5 wt %). Partial or full hydrotreatment can effectively lower the biocrude S content. Additionally, co-feeding with other low-sulfur wet wastes such as food waste can provide another option to produce raw biocrude with lower S content to meet the target with further hydrotreatment. This study indicates that biofuels could be a cost-effective fuel option for the marine sector. Marine biofuels derived from various feedstocks and conversion technologies could mitigate marine biofuel adoption risk in terms of feedstock availability and biorefinery economics.

1 December 2018
Verified
Report
Closed access
PDF file
MKMichael Kass
Michael Kass
ZAZia Abdullah
Zia Abdullah
MBMary J. Biddy
Mary J. Biddy
CDCorinne Drennan
Corinne Drennan
ZHZia Haq
Zia Haq
MWMichael Wang
Michael Wang
The U.S. Department of Energy's Office of Scientific and Technical Information

2 March 2021 in Energy & Fuels
Verified
Journal Article
Open access
MKMichael D. Kass
Michael D. Kass
CJChristopher J. Janke
Christopher J. Janke
RCRaynella Maggie Connatser
Raynella Maggie Connatser
SLSamuel Lewis
Samuel Lewis
The compatibility of 11 bioderivable diesel blendstocks with 17 elastomer materials common to fuel storage, dispensing, and delivery systems was evaluated though volume and hardness measurements. The blendstocks included two alcohols (1-octanol and 1-nonanol), two acid esters (methyl decanoate and hexyl hexanoate), tri(propylene glycol) methyl ether (TPM), butylcyclohexane, two ketones (2-nonanone and 2-pentanone), biodiesel, and renewable diesel. Each blendstock was blended with diesel in concentrations of 0, 10, 20, and 30 wt %. The elastomers included two fluorocarbons, six acrylonitrile butadiene rubbers (NBRs), and one each of fluorosilicone, neoprene, polyurethane, styrene butadiene rubber (SBR), hydrogenated acrylonitrile butadiene rubber (HNBR), a blend of NBR and PVC (OZO), epichlorohydrin/ethylene oxide (ECO), ethylene propylene diene monomer (EPDM), and silicone. Specimens of each elastomer material were immersed in the test fuels for a period of 4 weeks and measured for volume and hardness. Afterward, they were dried at 60 °C for 20 h and remeasured. The results showed that the alkanes, esters, and alcohols were suitable with many of the elastomers. For some materials, such as neoprene, these blendstocks improved the compatibility compared to neat diesel. In contrast, the ketones and TPM produced unsuitable volume expansion (>30%) and softening in many of the elastomers including the high-performance fluoroelastomers. Analysis of the results showed that the swelling behavior is predominantly due to polarity of the elastomer and test fuels.