A wideband hybrid dielectric resonator antenna (DRA) consisting of a rectangular slot patch and a perforated stacked cylindrical dielectric resonator (DR) is proposed. A rectangular slot was etched on the grounding side of a microwave laminate (ϵs =3.38) to excite the hybrid resonator at a high frequency. The stacked DR used consists of three different layers of permittivity, in which air-cavity was introduced internally to form a perforated structure. With a proper stacking arrangement of the perforated DRs on top of the rectangular slot, their operating frequencies were merged together to produce a wideband hybrid DRA. It was found that the combination of the stacked DR with perforated structure in the hybrid element had yielded an impedance bandwidth of as wide as 75.8% (12.2 GHz - 27.1 GHz). Huge improvement in bandwidth was successfully achieved in this study in comparison to that without a perforated structure of only 48.9%. Simulation of the antenna was performed in time domain using Computer Simulation Technology (CST) and was subsequently verified with the measurement results. The average simulated and measured directivity of the antenna were recorded to be 6.05 dBi and 5.65 dBi, respectively, with a stable broadside radiation throughout the operating range of frequency. The radiation characteristics were seen to be broadside in both the E-plane and H-plane.
The revolutionary microstrip technology for wireless communication suffers from relatively large size and low radiation efficiency when modeled for the current challenging hardware. An efficient solution to this subject is the quasi-lumped element (LE) approach. Therefore, this manuscript is a tutorial on the progress in quasi-LE resonator antennas, and it has been transcribed as an introduction or assessment for the readers. The paper traces the LEs’ history and fundamental principles. The modeling procedures of the quasi-LE resonator and its essential outline are summarized. A review of the quasi-LE resonator antennas for 5.8 GHz applications has been presented. Measurement reports of a unique quasi-LE antenna are also illustrated. Finally, the intended methods are compared with other configurations while considering the several important performance parameters of antennas.
The influence of La2O3 addition (x = 1,3,5 and 7 wt.%) on phases formation, microstructural and electrical properties of ZTA ceramic prepared via conventional solid-state method was studied by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and Hall Effect measurement, respectively. The XRD peaks show the presence of three different phases (Al2O3, Zr0.82Y0.18O1.91 and La0.85Al11.6O18.678). In addition, the bulk density of the present samples decreased remarkably while the porosity increases. The SEM results show that the grain morphology varies significantly with increasing La2O3 content. Increasing amount of La2O3 has increased the grain size which is beneficial to improve the electrical properties of ZTA system. The electrical resistivity of the ZTA-La2O3 composites ceramic decreased with increasing initial La2O3 content. The lowest electrical resistivity 13.2 (Ω.cm) was obtained for ZTA-7wt.% La2O3 composites ceramic. Therefore, the results confirm that better physical and electrical properties can be obtained by controlling amount of La2O3 addition into ZTA.
Barium Carbonate (BaCO3) was selected as dopant to examine its effect to the Potassium Sodium Niobate piezoelectric ceramic properties. In this work, the concentration of Barium was doped until highest stoichiometry disorder for stoichiometry ratio of K0.5Na0.5Nb3 (KNN). The mixed powder of KNN were calcined at 850 ˚C for 6 hours. Then the clean calcined powder was uniaxially-pressed about 200 MPa to produce green body pellet for 1 mm in thickness using Hydraulic Hand Press. The concentration of BaCO3 as dopant were ranged from 0.00 and 0.25 until 0.45. A green body pellet was conventionally sintered at 1120 °C for 2h in air atmosphere. A phase analysis was done using X-Ray Diffraction. Barium as dopant improve the density of KNN. The size of cubical grain in microstructure images were reduced with increasing Ba content indicate the phase transformation. The relative permittivity (467.74 to 26.85) and tangent loss (0.36726 to 0.24552) were reported decreasing trends at frequency of 1 kHz.