Qilun Zhang

Qilun Zhang

Auto-generated profile, based on publicly available information

Qilun Zhang

Laboratory of Organic Electronics Department of Science and Technology (ITN) Linköping University SE-60174 Norrköping Sweden

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2022 in Nature Communications
Verified
Journal Article
Open access
PDF file
XLXian’e Li
Xian’e Li
QZQilun Zhang
Qilun Zhang
JYJianwei Yu
Jianwei Yu
YXYe Xu
Ye Xu
RZRui Zhang
Rui Zhang
MFMats Fahlman
Mats Fahlman
Energy level alignment (ELA) at donor (D) -acceptor (A) heterojunctions is essential for understanding the charge generation and recombination process in organic photovoltaic devices. However, the ELA at the D-A interfaces is largely underdetermined, resulting in debates on the fundamental operating mechanisms of high-efficiency non-fullerene organic solar cells. Here, we systematically investigate ELA and its depth-dependent variation of a range of donor/non-fullerene-acceptor interfaces by fabricating and characterizing D-A quasi bilayers and planar bilayers. In contrast to previous assumptions, we observe significant vacuum level (VL) shifts existing at the D-A interfaces, which are demonstrated to be abrupt, extending over only 1–2 layers at the heterojunctions, and are attributed to interface dipoles induced by D-A electrostatic potential differences. The VL shifts result in reduced interfacial energetic offsets and increased charge transfer (CT) state energies which reconcile the conflicting observations of large energy level offsets inferred from neat films and large CT energies of donor - non-fullerene-acceptor systems.

20 December 2023 in Nature Communications
Verified
Journal Article
Open access
PDF file
TLTiefeng Liu
Tiefeng Liu
JHJohanna Heimonen
Johanna Heimonen
QZQilun Zhang
Qilun Zhang
CYChi-Yuan Yang
Chi-Yuan Yang
JHJun-Da Huang
Jun-Da Huang
SFSimone Fabiano
Simone Fabiano
Water-based conductive inks are vital for the sustainable manufacturing and widespread adoption of organic electronic devices. Traditional methods to produce waterborne conductive polymers involve modifying their backbone with hydrophilic side chains or using surfactants to form and stabilize aqueous nanoparticle dispersions. However, these chemical approaches are not always feasible and can lead to poor material/device performance. Here, we demonstrate that ground-state electron transfer (GSET) between donor and acceptor polymers allows the processing of water-insoluble polymers from water. This approach enables macromolecular charge-transfer salts with 10,000× higher electrical conductivities than pristine polymers, low work function, and excellent thermal/solvent stability. These waterborne conductive films have technological implications for realizing high-performance organic solar cells, with efficiency and stability superior to conventional metal oxide electron transport layers, and organic electrochemical neurons with biorealistic firing frequency. Our findings demonstrate that GSET offers a promising avenue to develop water-based conductive inks for various applications in organic electronics.

23 November 2023 in Advanced Science
Verified
Journal Article
Open access
CKChaoyang Kuang
Chaoyang Kuang
SCShangzhi Chen
Shangzhi Chen
MLMin Luo
Min Luo
QZQilun Zhang
Qilun Zhang
XSXiao Sun
Xiao Sun
MJMagnus Jonsson
Magnus Jonsson
Terahertz (THz) technologies provide opportunities ranging from calibration targets for satellites and telescopes to communication devices and biomedical imaging systems. A main component will be broadband THz absorbers with switchability. However, optically switchable materials in THz are scarce and their modulation is mostly available at narrow bandwidths. Realizing materials with large and broadband modulation in absorption or transmission forms a critical challenge. This study demonstrates that conducting polymer‐cellulose aerogels can provide modulation of broadband THz light with large modulation range from ≈ 13% to 91% absolute transmission, while maintaining specular reflection loss < −30 dB. The exceptional THz modulation is associated with the anomalous optical conductivity peak of conducting polymers, which enhances the absorption in its oxidized state. The study also demonstrates the possibility to reduce the surface hydrophilicity by simple chemical modifications, and shows that broadband absorption of the aerogels at optical frequencies enables de‐frosting by solar‐induced heating. These low‐cost, aqueous solution‐processable, sustainable, and bio‐friendly aerogels may find use in next‐generation intelligent THz devices.

1 February 2023 in Journal of Materials Chemistry C
Verified
Journal Article
Open access
PDF file
QZQilun Zhang
Qilun Zhang
YCYongzhen Chen
Yongzhen Chen
XLXianjie Liu
Xianjie Liu
MFMats Fahlman
Mats Fahlman
To better understand the effects of water and oxygen on OSC materials’ stability,i.e.PM6 and Y6, we usedin situnear-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) to investigate the electronic structures.

14 December 2023 in Advanced Materials
Verified
Journal Article
Open access
QZQilun Zhang
Qilun Zhang
TLTiefeng Liu
Tiefeng Liu
SWSebastian Wilken
Sebastian Wilken
SXShaobing Xiong
Shaobing Xiong
HZHuotian Zhang
Huotian Zhang
MFMats Fahlman
Mats Fahlman
Herein, a binary cathode interface layer (CIL) strategy based on the industrial solvent fractionated LignoBoost kraft lignin (KL) is adopted for fabrication of organic solar cells (OSCs). The uniformly distributed phenol moieties in KL enable it to easily form hydrogen bonds with commonly used CIL materials, i.e., bathocuproine (BCP) and PFN‐Br, resulting in binary CILs with tunable work function (WF). This work shows that the binary CILs work well in OSCs with large KL ratio compatibility, exhibiting equivalent or even higher efficiency to the traditional CILs in state of art OSCs. In addition, the combination of KL and BCP significantly enhanced OSC stability, owing to KL blocking the reaction between BCP and nonfullerene acceptors (NFAs). This work provides a simple and effective way to achieve high‐efficient OSCs with better stability and sustainability by using wood‐based materials.

9 June 2022 in Solar RRL
Verified
Journal Article
Open access
QZQilun Zhang
Qilun Zhang
HZHuotian Zhang
Huotian Zhang
ZWZiang Wu
Ziang Wu
CWChuanfei Wang
Chuanfei Wang
RZRui Zhang
Rui Zhang
MFMats Fahlman
Mats Fahlman
Introduction of filler materials into organic solar cells (OSCs) are a promising strategy to improve device performance and thermal/mechanical stability. However, the complex interactions between the state‐of‐the‐art OSC materials and filler require careful selection of filler materials and OSC fabrication to achieve lower cost and improved performance. In this work, the introduction of a natural product betulin‐based insulating polymer as filler in various OSCs is investigated. Donor–acceptor–insulator ternary OSCs are developed with improved open‐circuit voltage (Voc) due to decreased trap‐assisted recombination. Furthermore, filler‐induced vertical phase separation due to mismatched surface energy can strongly affect charge collection at the bottom interface and limit the filler ratio. A quasi‐bilayer strategy is used in all‐polymer systems to circumvent this problem. Herein, the variety of filler materials in OSCs to biomass is broadened, and the filler strategy is made a feasible and promising strategy toward highly efficient, eco, and low‐cost OSCs.