Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting. Hot work toll steels are usually produced by ingot metallurgy, but also by powder metallurgy, namely hot isostatic pressing and powder forging routes. In this paper we investigate the possibility of production of a hot work tool steel (AISI H13) by conventional (die compaction and pressureless sintering) and metal injection molding routes, aiming to reduce cost and production time. The sintering behavior was studied from 1250 °C until 1430 °C and the resulting parts were compared in terms of microstructure, hardness and tensile strength. The results showed that both shaping routes together with pressureless sintering are suitable to produce this alloy. By combining the best shaping approach and a tailored sintering cycle, it was possible to produce samples with 400 HV10 as well as tensile strength of 1 GPa, which are comparable to the ones obtained by powder forging.
Zirconia nanoceramics are interesting materials for numerous high-temperature applications. Because their beneficial properties are mainly governed by the crystal and microstructure, it is essential to understand and control these features. The use of co-stabilizing agents in the sol-gel synthesis of zirconia submicro-particles should provide an effective tool for adjusting the particles’ size and shape. Furthermore, alumina-doping is expected to enhance the particles’ size and shape persistence at high temperatures, similar to what is observed in corresponding bulk ceramics. Dispersed alumina should inhibit grain growth by forming diffusion barriers, additionally impeding the martensitic phase transformation in zirconia grains. Here, alumina-doped zirconia particles with sphere-like shape and average diameters of were synthesized using a modified sol-gel route employing icosanoic acid and hydroxypropyl cellulose as stabilizing agents. The particles were annealed at temperatures between 800 and 1200 and characterized by electron microscopy, elemental analysis, and X-ray diffraction. Complementary elemental analyses confirmed the precise control over the alumina content (0–50 mol%) in the final product. Annealed alumina-doped particles showed more pronounced shape persistence after annealing at 1000 than undoped particles. Quantitative phase analyses revealed an increased stabilization of the tetragonal/cubic zirconia phase and a reduced grain growth with increasing alumina content. Elemental mapping indicated pronounced alumina segregation near the grain boundaries during annealing.
13 June 2015 in Journal of the American Ceramic Society
Atomic layer deposition (ALD) process presents thickness control in an Ångstrom scale due to its inherent surface self‐limited reactions. In this work, an ALD super cycle approach, where a superposition of nanolaminates of SiO2 and Al2O3 is generated by cycling the precursors APTES–H2O–O3 and TMA–H2O, is used to deposit thin films with varying ratio of Al2O3:SiO2 into silicon wafers and into inverse photonic crystals. The resulting ternary oxide films deposited at low temperature (150 °C) are amorphous. However, conversion to mullite occurs at 1000 °C, way below the conversion temperatures found into powder processing or diphasic sol–gel routes (type II) and comparable to monophasic sol–gel synthesis. By means of such a mullite coating, the structural stability of an Al2O3 inverse photonic crystal is increased up to 1400 °C.
21 August 2018 in Journal of the American Ceramic Society
Three‐dimensionally ordered macroporous materials for photonic or refractory applications have been developed by an innovative approach based on mullite sol‐gel infiltration of direct photonic crystals followed by burn‐out and calcination. Direct photonic crystals were obtained using polystyrene spheres templates either by vertical convective self‐assembly or by drop casting. The samples were then infiltrated by spin coating with mullite sol‐gels prepared with two different compositions (74 wt.% Al 2 O 3 , 26 wt.% SiO 2 and 80 wt.% Al 2 O 3 , 20 wt.% SiO 2 ). The inverse opal photonic crystals prepared with both sol‐gels presented a highly ordered porosity and the high‐alumina composition showed stability up to 1500°C. After inversion of the structure (polymeric template burn‐out), the high‐alumina composition showed roundness of the PS templated pores closer to an ideal sphere (Ø = 0.967) when compared to the low‐alumina composition (Ø = 0.954). Although the inverse opal photonic crystals did not present a photonic bandgap, they showed structural stability at high temperatures, which enable their application as refractory materials.