9 May 2022 in Superconductor Science and Technology
The structural and chemical composition of the surface layer (100–140 nm) of niobium radiofrequency cavities operating at cryogenic temperature has enormous impact on their superconducting characteristics. During the last years, cavities treated with a new thermal processing recipe, so-called nitrogen infusion, have demonstrated an increased efficiency and high accelerating gradients. The role and importance of nitrogen gas has been a topic of many debates. In the present work we employ variable-energy synchrotron x-ray photoelectron spectroscopy (XPS), to study the niobium surface subjected to the following treatments: vacuum annealing at 800 °C, nitrogen infusion, and vacuum heat treatment as for the infusion process but without nitrogen supply. Careful analysis of XPS energy-distribution curves revealed a slightly increased thickness of the native oxide Nb2O5 for the infused samples (∼3.8 nm) as compared to the annealed one (∼3.5 nm) which indicates insignificant oxygen incorporation into niobium during 120 °C baking and no effect of nitrogen on the formation of oxides or other niobium phases. By conducting an additional in-situ annealing experiment and analyzing the niobium after the failed infusion process, we conclude that the vacuum furnace hygiene particularly during the high-temperature stage is the prerequisite for success of any treatment recipe.
6 June 2024 in Superconductor Science and Technology
In order to determine optimal parameters of vacuum thermal processing of superconducting radiofrequency niobium cavities exhaustive information on the initial chemical state of niobium and its modification upon a vacuum heat treatment is required. In the present work the chemical composition of the niobium surface upon ultra-high vacuum baking at 200 ∘C–400 ∘C similar to ‘medium-temperature baking’ and ‘furnace baking’ of cavities is explored in-situ by synchrotron x-ray photoelectron spectroscopy (XPS). Our findings imply that below the critical thickness of the layer ( ) niobium starts to interact actively with surface impurities, such as carbon and phosphorus. By studying the kinetics of the native oxide reduction, the activation energy and the rate-constant relation have been determined and used for the calculation of the oxygen-concentration depth profiles. It has been established that the controlled diffusion of oxygen is realized at temperatures 200 ∘C–300 ∘C, and the native-oxide layer represents an oxygen source, while at 400 ∘C the pentoxide is completely reduced and the doping level is determined by an ambient oxygen partial pressure. Fluorine (F to Nb atomic ratio is 0.2) after the buffered chemical polishing was found to be incorporated into the surface layer probed by XPS ( ), and its concentration increased during the low-temperature baking (F/Nb = 0.35 at 230 ∘C) and depleted at higher temperatures (F/Nb = 0.11 at 400 ∘C). Thus, the influence of fluorine on the performance of mid-T baked, nitrogen-doped and particularly mild-baked (120 ∘C/48 h) cavities must be considered. The possible role of fluorine in the educed reaction under the impact of an x-ray beam at room temperature and during the thermal treatment is also discussed. The range of temperature and duration parameters of the thermal treatment at which the niobium surface would not be contaminated with impurities is determined.
17 March 2025 in Superconductor Science and Technology
Vacuum thermal treatments (baking) are known to improve the superconducting properties of the RF surface layer of niobium cavities, and are employed as a last processing step to increase their efficiency determined by intrinsic quality factor Q 0. A specific method to perform the baking has been used. It consists in annealing of an evacuated cavity with the local heaters installed on its outer surface in a cryostat which ensures an exterior vacuum and protects the outer cavity surface from oxidation. Such a set-up has a number of advantages as it does not require to cool the cavity flanges during baking, and allows to perform the ‘cold’ RF characterization of the cavity in situ, immediately after the thermal treatment without disassembly of heating elements. Moreover, the air exposure that causes partial degradation of Q 0 by surface reoxidation is avoided. The heat treatment of a single-cell 1.3 GHz niobium cavity at 230 ∘C for 24 h demonstrated the doubling of Q 0 at = 10 MV m−1 (from to ) and retained the maximal accelerating field of 35 MV m−1 without quenching. The selection of treatment parameters is based on our previous XPS studies. This treatment ensures incomplete dissolution of the native oxide by oxygen diffusion, thereby preventing interaction of niobium surface with external contaminants. We propose to bake the cavities directly in a cryomodule, which would allow to use the treatment to improve their performance. The potential impact of material parameters on the components of surface resistance has been briefly examined.
27 June 2014 in Advances in Materials Science and Applications
20 March 2025 in Superconductor Science and Technology
Upon reviewing the published version of our work, we identified misprints in the equations, which are corrected here. Additionally, we re-evaluated the oxygen concentration depth profiles. This re-evaluation does not affect the validity of the paper’s statements or conclusions.
7 May 2024 in Engineering Research Express
Two niobium elliptical 1.3 GHz superconducting radio frequency (SRF) electron photoinjector cavities were successfully recovered after mechanical inner surface damage. Both cavities had deep imprints in the critical high surface electric field area around the photoelectric cathode position. The lengthy repair procedure, which consists of surface inspection and defect characterization, mechanical polishing and light chemical etching is described in detail. In the process, a new high pressure rinsing (HPR) nozzle system optimized for the special photoinjector geometry was also developed. Subsequent cold RF tests demonstrate complete performance recovery. This is the first time that photoinjector cavities damaged in the high electric-field region could be recovered.