Wide-bandgap (WBG) perovskite solar cells (PSCs) attract intensive attention because of their high tandem compatibility and versatile application scenarios. However, severe interfacial non-radiative recombination of mixed-ion WBG perovskite films was caused by complex defect types and phase impurities, leading to deteriorated device performance and stability. Herein, a rational surface heterostructure design was achieved by precisely constructing a two-dimensional Dion–Jacobson layer atop the 3D WBG layer by inhibiting surface side reactions. A dual-ammonium strategy was screened out to block undesired molecular interactions, refining surface lattice structures and energy landscapes to interfacial defect reduction, charge transport acceleration, and phase stability prolongation. A champion WBG PSC (active area: 0.10 cm2) based on the optimized 1.68 eV perovskite film achieved an impressive efficiency of 23.05% (certified 22.58%) with an open-circuit voltage of 1.25 V, plus a large-area (1.00 cm2) efficiency exceeding 21.25% and a mini-module (7.26 cm2) efficiency of 20.10%.
Halide perovskites exhibit superior optoelectronic properties but lack precise thickness and band offset control in heterojunctions, which is critical for modular multilayer architectures such as multiple quantum wells. We demonstrate vapor-phase, layer-by-layer heteroepitaxial growth exemplified by CsPbBr 3 deposition on single crystals of PEA 2 PbBr 4 (PEA: 2-phenylethylammonium). Angstrom-level thickness control and subangstrom smooth layers enable quantum-confined photoluminescence of CsPbBr 3 from monolayer, bilayer, and through to bulk. The interfacial structure controls the electronic structure from a Cs‒PEA-terminated interface (type II heterojunction) to a PEA‒PEA-terminated interface (type I heterojunction), with a layer-tunable band offset shift exceeding 0.5 electron volts. Electron transfer from CsPbBr 3 to PEA 2 PbBr 4 for a type II Cs‒PEA heterojunction results in delayed electron-hole recombination beyond 10 microseconds. Precise quantum confinement control and large band offset tunability unlock perovskite heterojunctions as platforms for scalable, superlattice-based optoelectronic applications.
25 August 2023 in ACS Applied Materials & Interfaces
Cu3BiS3 thin films are fabricated via spin coating of precursor solutions containing copper and bismuth xanthates onto planar glass substrates or mesoporous metal oxide scaffolds followed by annealing at 300 °C to convert the metal xanthates into copper bismuth sulfide. Detailed insights into the film formation are gained from time-resolved simultaneous small and wide angle X-ray scattering measurements. The Cu3BiS3 films show a high absorption coefficient and a band gap of 1.55 eV, which makes them attractive for application in photovoltaic devices. Transient absorption spectroscopic measurements reveal that charge generation yields in mesoporous TiO2/Cu3BiS3 heterojunctions can be significantly improved by the introduction of an In2S3 interlayer, and long-lived charge carriers (t50% of 10 μs) are found.
Blue gallium nitride (GaN) light‐emitting diodes (LEDs), combined with red/green fluorescent converters, have broad potential for display applications. Metal halide perovskites now show excellent luminescence properties and may be suitable as light converters. Here a simple solution‐processed method is reported to prepare a methylammonium lead bromide (MAPbBr3) nanoporous GaN composite. Fast (within 2 ps) energy transfer is demonstrated from photoexcited nanoporous GaN to encapsulate MAPbBr3 nanocrystals, as observed by transient absorption spectroscopy. The spatial confinement of the perovskite within the nanoporous GaN is shown to increase the perovskite radiative recombination rate. These results offer guidelines for developing high‐performance perovskite/nanoporous GaN optoelectronics.
Perovskite light-emitting diodes (PeLEDs) are promising low-cost, solution-processable, and color-pure optoelectronic devices for display and lighting applications. However, blue PeLEDs continue to lag their green and red counterparts in terms of luminance and operational lifetime, limiting their practical implementation. The performance disparity primarily arises from charge injection imbalance, which accelerates degradation at the perovskite/hole transport layer (HTL) interface under electrical bias. Here, we design a polymer blend HTL comprising poly( N -vinyl-2,7-difluoro-carbazole) (PVK-F) and poly(bis(4-phenyl)(2,4,6-trimethylphenyl)amine) (PTAA), in which strengthened van der Waals interactions promote denser molecular packing. This optimized microstructure simultaneously enhances hole mobility and wettability, enabling high-quality perovskite film formation. Consequently, PeLEDs emitting at 485 nanometers achieve an external quantum efficiency of 24.1% and luminance exceeding 26,000 candela per square meter. Moreover, the improved hole injection mitigates interfacial degradation, yielding an operational half-lifetime exceeding 700 minutes at an initial luminance of 100 candela per square meter. This work establishes polymer blending as an effective strategy for advancing the performance and stability of blue PeLEDs.