J. R. Arias

J. R. Arias

Auto-generated profile, based on publicly available information

J. R. Arias

Technical University of Madrid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2012 in Applied Thermal Engineering
Verified
Journal Article
Closed access
MRM. Reyes
M. Reyes
DAD. Alonso
D. Alonso
JAJ.R. Arias
J.R. Arias
Angel VelazquezAngel Velazquez
Angel Velazquez

1 April 2008 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Open access
Angel VelazquezAngel Velazquez
Angel Velazquez
JAJ.R. Arias
J.R. Arias
BMB. Mendez
B. Mendez
This study is motivated by the need to devise means to enhance heat transfer in configurations, like the back step, that appear in certain types of MEMS that involve fluid flow and that are not very efficient from the thermal transfer point of view. In particular, the work described in this paper studies the effect that a prescribed flow pulsation (defined by two control parameters: velocity pulsation frequency and pressure gradient amplitude at the inlet section) has on the heat transfer rate behind a backward facing step in the unsteady laminar 2-D regime. The working fluid that we have considered is water with temperature dependent viscosity and thermal conductivity. We have found that, for inlet pressure gradients that avoid flow reversal at both the upstream and downstream boundary conditions, the timeaveraged Nusselt number behind the step depends on the two above mentioned control parameters and is always larger than in the steady-state case. At Reynolds 100 and pulsating at the resonance frequency, the maximum time-averaged Nusselt number in the horizontal wall region located behind the step whose length is four times the step height is 55% larger than in the steady-case. Away from the resonant pulsation frequency, the time-averaged Nusselt number smoothly decreases and approaches its steady-state value

1 April 2011 in Applied Thermal Engineering
Verified
Journal Article
Open access
MRM. Reyes
M. Reyes
JAJ.R. Arias
J.R. Arias
Angel VelazquezAngel Velazquez
Angel Velazquez
José M VegaJosé M Vega
José M Vega
This article presents an experimental study on the optimisation of micro-heat sink configurations when both thermal effects and pressure drop are accounted for. The interest of the latter is that the practical engineering viability of some of these systems also depends on the required pumping power. The working fluid was water and, according to typical power dissipation and system size requirements, the considered fluid regime was either laminar or transitional, and not fully developed from the hydrodynamics point of view. Five configurations were considered: a reference geometry (selected for comparison purposes) made up of square section micro-channels, and four alternative configurations that involved the presence of a variable tip clearance in the design. The performance of the different configurations was compared with regard to both cooling efficiency and pressure drop. Finally, we also provide some practical guidelines for the engineering design of these types of systems

1 May 2010 in International Communications in Heat and Mass Transfer
Verified
Journal Article
Closed access
STS. Terhaar
S. Terhaar
Angel VelazquezAngel Velazquez
Angel Velazquez
JAJ.R. Arias
J.R. Arias
MSMario Sanchez
Mario Sanchez

1 January 2009 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Open access
Angel VelazquezAngel Velazquez
Angel Velazquez
JAJ.R. Arias
J.R. Arias
José Luis Luis Montañés GarcíaJosé Luis Luis Montañés García
José Luis Luis Montañés García
This paper deals with the study of 2-D, laminar, pulsating flow inside a heated rectangular cavity with different aspect ratios. The cooling liquid (water with temperature dependent viscosity and thermal conductivity) comes and leaves the cavity via inlet and outlet ports. The flow topology is characterised by the large recirculation regions that exist at inner corners of the cavity. These low velocity regions cause the heat transfer to be small when compared, for instance, to that of a straight channel. We study the effect that a prescribed pulsation at the inlet port has on the cavity heat transfer. This pulsating boundary condition, of the unsteady Poiseuille type, is described by its frequency and the amplitude of the pressure gradient. The time averaged Reynolds number of the flow, based on the hydraulic diameter of the inlet channel, is 100 and we consider that the dimensionless pulsation frequency (Strouhal number) varies in the range from 0.0 to 0.4. We show that the prescribed pulsation enhances heat transfer in the cavity and that the mechanism that causes this enhancement appears to be the periodic change in the recirculation flow pattern generated by the pulsation. Regarding the quantitative extent of heat transfer recovery, we find that appropriate selection of the pulsation parameters allows for the cavity to behave like a straight channel that is the configuration with the highest Nusselt number

1 November 2011 in Control Engineering Practice
Verified
Journal Article
Closed access
NBN. Benito
N. Benito
JAJ.R. Arias
J.R. Arias
Angel VelazquezAngel Velazquez
Angel Velazquez
José M VegaJosé M Vega
José M Vega