30 June 2022 in Aerosol Science and Technology
A model flow reactor provides a narrow particle temperature-residence time distribution with well-defined conditions and is mandatory to measure changes of the particle structure precisely. The experimental data of iron and iron oxide agglomerates are used to determine the sintering kinetics considering the temperature-time history of the particles. Thousand particle trajectories are tracked in a validated CFD model at three different furnace temperatures each. Strongly agglomerated particles with a small primary particle size (∼4 nm) are synthesized by spark discharge and are size-selected (25–250 nm) before sintering. The structure development is measured simultaneously with different online instrumentations and the structure calculated by means of structure models. A simple sintering model, based on the reduction of surface energy, is numerically quantified with the experimental results. The surface of the particles is strongly dependent on the primary particle size and the agglomerate structure. The chemical phase is analyzed using the offline techniques XANES, XRD, and EELS. It is observed that the addition of hydrogen led to a reduction of iron oxide to iron nanoparticles and to changes of the sintering kinetics. The sintering exponent = 1 was found to be optimal. For Fe, an activation energy of 59.15 kJ/mol and a pre-exponential factor of 1.57 104 s/m were found, for Fe3O4 an activation energy of 55.22 kJ/mol and a pre-exponential factor of 2.54 104 s/m. Copyright © 2022 American Association for Aerosol Research
12 September 2022 in Scientific Reports
A novel chemical vapor synthesis reactor design is used to control the pore-particle mesostructure and investigate the pore formation mechanism through the variation of residence time in oxygen. This enables the exploitation of the Kirkendall effect at the nanoscale to generate ultrasmall pores in small nanocrystalline iron oxide particles. Detailed structural characterization and quantitative data analysis of complementary high resolution transmission electron microscopy images, X-ray diffractograms, nitrogen sorption isotherms and X-ray absorption spectra provide a consistent comprehensive picture of the hollow nanoparticles from the local to the microstructure. The pore formation mechanism seems to play a key role for β-Fe2O3 polymorph formation.
17 July 2023 in Applications in Energy and Combustion Science
1 June 2020 in Review of Scientific Instruments
Technologically relevant gas phase processes rely on reactants in vapor form for the production of thin films and nanoparticles. An instrument is described which enables the investigation of such vapors by x-ray absorption spectroscopy. Corresponding in situ studies provide information about gas phase precursor chemistry and optimized synthesis processes. The setup consists of a sealed vapor container heated by a hot air bath. Inert gas filling and temperature monitoring are implemented. Fluid dynamic simulations reveal a homogeneous temperature distribution without hot or cold spots. Temperature stability better than 1 K for at least 190 min allows time-dependent measurements or improved signal to noise ratios by averaging of datasets. Iron acetylacetonate is studied as a model system. X-ray absorption spectra measured by fluorescence are of high quality, allowing a detailed analysis of X-ray Absorption Near Edge Structure (XANES) and extended x-ray absorption fine structure. A molecular structure transformation is observed in XANES spectra of iron acetylacetonate vapor above 480 K probably due to the loss of one ligand. The setup allows the investigation of low volatility compounds with vapor pressures above 2 kPa at temperatures up to 520 K.
1 November 2022 in Review of Scientific Instruments
We describe a versatile reactor system for chemical vapor synthesis of nanoparticles, which enables in situ investigations of high temperature gas phase particle formation and transformation processes by x-ray scattering and x-ray absorption spectroscopy. The system employs an inductively heated hot wall reactor as the energy source to start nanoparticle formation from a mixture of precursor vapor and oxygen. By use of a modular set of susceptor segments, it is especially possible to change solely the residence time of the gas mixture while keeping all other process parameters (temperature, gas flow, pressure) constant. Corresponding time–temperature profiles are supported by computational fluid dynamics simulations. The operation of the system is demonstrated for two example studies: tin oxide nanoparticle formation studied by small angle x-ray scattering and iron oxide nanoparticle formation by x-ray absorption spectroscopy.
30 January 2018 in MRS Advances