2 July 2020 in ACS Applied Materials & Interfaces
7 March 2019 in Scientific Reports
Natural carbon powder has been used as a precursor to prepare two main types of sensitising agents of nitrogen-doped carbon nanoparticles (N-CNPs) and nitrogen-doped graphene quantum dots coupled to nanosheets (N-GQDs-NSs) by using simple treatments of chemical oxidation and centrifugation separation. Characterization based on FTIR, XPS, XRD, Raman spectroscopy, FE-SEM, HR-TEM, AFM, UV-Vis and FL, revealed successful doping carbon nanoparticle with nitrogen with an average plane dimension of 50 nm and relatively smooth surface. The versatility of the prepared samples as sensitising agents was developed and established by exploiting its ability for detection of volatile organic compounds via simple optical fibre based sensing configuration. The comparative experimental studies on the proposed sensor performance indicate fast response achieved at a few tens of seconds and excellent repeatability in exposure to the methanol vapour. The low limit of detection of 4.3, 4.9 and 10.5 ppm was obtained in exposure to the methanol, ethanol and propanol vapours, respectively, in the atmosphere condition. This study gives insights into the chemical/physical mechanism of an enhanced economic optical fibre based gas sensor and illustrates it for diverse sensing applications, especially for chemical vapour remote detection and future air quality monitoring.
25 August 2020 in ACS Omega
Graphene sensitization of glucose-imprinted polymer (G-IP)-coated optical fiber has been introduced as a new biosensor for evanescent wave trapping on the polymer optical fiber to detect low-level glucose. The developed sensor operates based on the evanescent wave modulation principle. Full characterization via atomic force microscopy (AFM), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, high-resolution transmission electron microscopy (HRTEM), and N2 adsorption/desorption of as-prepared G-IP-coated optical fibers was experimentally tested. Accordingly, related operational parameters such as roughness and diameter were optimized. Incorporating graphene into the G-IP not only steadily promotes the electron transport between the fiber surface and as-proposed G-IP but also significantly enhances the sensitivity by acting as a carrier for immobilizing G-IP with specific imprinted cavities. The sensor demonstrates a fast response time (5 s) and high sensitivity, selectivity, and stability, which cause a wide linear range (10–100 nM) and a low limit of detection (LOD = 2.54 nM). Experimental results indicate that the developed sensor facilitates online monitoring and remote sensing of glucose in biological liquids and food samples.
4 December 2010 in Laser Physics
A simple technique for achieving multi-wavelength tunable multi-wavelength Brillouin fiber laser (BFL) based on dual-pass configuration is demonstrated. The BFL uses a piece of 10 km long non-zero dispersion shifted fiber (NZ-DSF) as a Brillouin gain medium to obtain odd-order Brillouin Stokes waves as an output with the line spacing of 0.16 nm (20 GHz) between each two consecutive waves by employing even-order Brillouin Stokes to improve output performance of the laser. With a BP of 15.3 dBm, at least 15 odd-order Brillouin Stokes and anti-Stokes lines are generated. The laser is room temperature stable, tunable over 50 nm wavelength range and has an optical signal to noise ratio of more than 30 dB at 1560 nm region. This Brillouin fiber laser can operate at any wavelength depending on the Brillouin pump (BP) wavelength used.
19 December 2022 in Nanoscale Advances
For the first time, in this study, a novel optical fiber biosensor is proposed and developed via coating only one smart functional layer of silica-supported carbon dots realizing the concepts of both lossy mode resonance (LMR) and molecularly imprinted polymer (MIP) for epinephrine detection. The carbon quantum dots (CQDs) are prepared using a green synthesis method and then treated with a molecularly imprinted polymer (MIP) strategy. Under ultrasonic irradiation, a SiO2 shell was stabilized on the surface of the CQDs to graft and to provide the LMR/MIP functional layer onto the curved optical fiber surface. Accurate structural and morphological characterization confirmed the carbon quantum dot agents and also the SiO2 supporting shells on the optical fiber, while spectroscopic analysis confirms the formation of the imprinted polymer and desirable absorbance characteristics. The experimental and numerical sensing studies revealed that the proposed sensing probe allows the rapid adsorption/desorption of epinephrine to the sensing films and highly permeable coating for studying the influence of effective parameters. Under the optimal experimental conditions, the sensitivity of the proposed LMR-based optical fiber sensor is reported to be 0.37 nm μM−1 with a correlation coefficient of 0.99. So, sensitive detection of epinephrine at a low concentration can be guaranteed with a 0.72 mM LOD.
20 November 2017 in Journal of Electronic Materials